manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 177

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

155

Print Engine Controller Test Prints

The Print Engine Controller Board Test Prints require entering Diagnostics Mode.  Refer 

to page 1-154 for instructions on how to enter Diagnostics Mode.

The Control Panel Test Legend to the right will aid in 
navigating through the variety of test prints available.

Table 1-103 Print Engine Controller Test Prints

Press [1] or [5] to display: 

Þ

Main Menu
Print Menu

Press [2] or [6]  to display: 

ß

Press [3] or [7] to display: 

ß

Comment

Test Print
Start Print

Press [4] to start the test print 
selected.  Press [0] to stop.

Test Print
Print Quantity

Print Quantity
1*

Press [3] or [7] until desired 
quantity is selected (1~999), 
then press [4].  

Test Print
Input Tray

Input Tray
Tray 1*

Press [4] to select the paper 
feed tray desired.  

Input Tray
Tray 2

Press [4] to select the paper 
feed tray desired. 

Input Tray
Tray 3

(1)

Press [4] to select the paper 
feed tray desired. 

Input Tray
Tray 4

(1)

Press [4] to select the paper 
feed tray desired. 

Input Tray
Tray 5

(1)

Press [4] to select the paper 
feed tray desired. 

Input Tray
MBF/ENV

(4)

Multi-sheet Bypass Feeder or 
Envelope Feeder

Test Print
Output Tray

Output Tray
Face Down*

Press [4] to select the output 
Tray desired.  
This selection outputs to the 
Face Down output Tray using 
no offset.

Output Tray
Face Dw F Offset

Outputs to the Face Down 
output Tray using front offset

Output Tray
Face Dw R Offset

Outputs to the Face Down 
output Tray using rear offset

Output Tray
Face  up

(2)

Outputs to the Face up tray

Output Tray
Finisher

(3)

Outputs to the Finisher

Test Print
Duplex

Duplex
Off*

Single side printing

Duplex
On

Both sides of page printed

Test Print
Staple Selection

Staple Selection
No Staple*

(3)

Staple Selection
Front Staple

(3)

45

o

 relative to the front 

(Control Panel side) of the 
printer 

Stop

Start

Menu Up

Item Up

Value Up

Menu
Down

 Item
Down

Value
Down

S4525-25B

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands