manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 165

Volume 1 / Print Engine - Troubleshooting

1

-

143

RAP 1-76

Lead Edge Registration Is Not Correct

.

PROBLEM

The printed image is not centered on the page.  The lead 
edge margin of the printed image is either too narrow or too 
wide, and either cuts off the lead edge of the printer image or 
starts the lead edge of the printed image too far into the page.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-31  Lead Edge Registration Is Not Correct

Table 1-100 Lead Edge Registration Is Not Correct

Step

Actions and Questions

Yes

No

1

PAPER Tray INSPECTION

Inspect the paper that is loaded in the paper Bin.

Is the paper loaded correctly and are the paper 
guides adjusted correctly?

Go to step 2

Reload the 
paper and 
adjust the 
paper guides

2

LEAD EDGE REGISTRATION

Refer to the Diagnostics, Test Prints, Service Tests & 
NVRAM Adjustments section of this manual and use 
NVRAM to adjust Lead Edge Registration.

Can you adjust lead edge registration using 
NVRAM?

Problem 
solved

Go to step 3

3

1. Reload print driver software.
2. Generate 5 Test Prints.

Is the lead edge registration correct?

Problem 
solved

Go to step 4

4

1. Replace the Print Engine Controller Board (RRP 1-72)
2. Generate 5 Test Prints.

Is the lead edge registration correct?

Problem 
solved

Go to step 5

5

1. Replace the Laser Scanner (RRP 1-47)
2. Generate 5 Test Prints.

Is the lead edge registration correct?

Problem 
solved

 Go to step 6

S4525-22

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands