Xerox C235, Quick Reference Manual

Page: 10 / 16

• Load letterhead with the printable side face-down and the top
edge entering the printer last for two-sided printing.
• Load envelope with the flap side down and against the right
side of the paper guide.
3. Feed the paper until its leading edge gets pulled in.
• To avoid paper jams, do not force paper into the manual
feeder.
• Before loading another sheet, wait for a message to appear
on the display.
SSeettttiinngg tthhee PPaappeerr SSiizzee aanndd TTyyppee
1. From the control panel, navigate to:
Settings > OK > Paper > OK > Tray Configuration > OK > Paper
Size/Type > OK
, then select a paper source
2. Set the paper size and type.
U Uppddaattiinngg FFiirrm mw waarree
Some applications require a minimum device firmware level to
operate correctly.
For more information on updating the device firmware, contact your
customer service representative.
1. Open a web browser, and then type the printer IP address in the
address field.
• View the printer IP address on the printer home screen. The IP
address appears as four sets of numbers separated by periods,
such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the web page correctly.
2. Click Settings > Device > Update Firmware .
3. Choose one of the following:
• Click Check for updates > I agree, start update .
• Upload the flash file. To upload the flash file, perform the
following steps.
To get the latest firmware, go to www.xerox.com , and search for
your printer model.
1. Browse to the flash file.
Note: Make sure that you have extracted the firmware
zip file.
2. Click Upload > Start .
C Coonnnneeccttiinngg tthhee PPrriinntteerr ttoo aa W Wii--FFii N Neettw woorrkk
Before you begin, make sure that:
• Active Adapter is set to Auto. From the home screen, touch
Settings > Network/Ports > Network Overview > Active Adapter .
• The Ethernet cable is not connected to the printer.
U Ussiinngg tthhee w wiirreelleessss sseettuupp w wiizzaarrdd iinn tthhee pprriinntteerr
Before using the wizard, make sure that the printer firmware is
updated. For more information, see
Updating Firmware .
1. From the home screen, touch > Set up now .
2. Select a Wi-Fi network, and then type the network password.
3. Touch Done .
U Ussiinngg tthhee SSeettttiinnggss M Meennuu iinn tthhee PPrriinntteerr
1. From the home screen, touch Settings > Network/Ports >
Wireless > Setup On Printer Panel > Choose Network .
2. Select a Wi-Fi network, then type the network password.
Note: For Wi-Fi-network-ready printer models, a prompt to
set up the Wi-Fi network appears during initial setup.
C Coonnffiigguurriinngg W Wii--FFii D Diirreecctt
Wi-Fi Direct is a Wi-Fi-based peer-to-peer technology that allows
wireless devices to connect directly to a Wi-Fi Direct-enabled printer
without using an access point (wireless router).
1. From the home screen, touch Settings > Network/Ports > Wi-Fi
Direct .
2. Configure the settings.
• Enable Wi-Fi Direct —Enables the printer to broadcast its own
Wi-Fi Direct network.
• Wi-Fi Direct Name —Assigns a name for the Wi-Fi Direct
network.
• Wi-Fi Direct Password —Assigns the password for negotiating
the wireless security when using the peer-to-peer connection.
• Show Password on Setup Page —Shows the password on the
Network Setup Page.
• Auto-Accept Push Button Requests —Lets the printer accept
connection requests automatically.
Note: Accepting push-button requests automatically is not
secured.
• By default, the Wi-Fi Direct network password is not visible on
the printer display. To show the password, enable the
password peek icon. From the home screen, touch
Settings >
Security > Miscellaneous > Enable Password/PIN Reveal .
• To know the password of the Wi-Fi Direct network without
showing it on the printer display, from the home screen touch
Settings > Reports > Network > Network Setup .
C Coonnnneeccttiinngg aa ccoom mppuutteerr ttoo tthhee pprriinntteerr
Before connecting your computer, make sure that Wi-Fi Direct has
been configured. For more information, see
Configuring Wi-Fi Direct .
10