Xerox AltaLink B81 Series User Manual Download Page 13 | Manualshive

Page: 13 / 404

background image

Electrical Safety

G

Geenneerraall G

Guuiiddeelliinneess

WARNING:

• Do not push objects into slots or openings on the printer. Touching a voltage point or

shorting out a part could result in fire or electric shock.

• Do not remove the covers or guards that are fastened with screws unless you are installing

optional equipment and are instructed to do so. Power off the printer when performing
these installations. Disconnect the power cord when removing covers and guards for
installing optional equipment. Except for user-installable options, there are no parts that
you can maintain or service behind these covers.

The following are hazards to your safety:

• The power cord is damaged or frayed.

• Liquid is spilled into the printer.

• The printer is exposed to water.

• The printer emits smoke, or the surface is unusually hot.

• The printer emits unusual noise or odors.

• The printer causes a circuit breaker, fuse, or other safety device to activate.

If any of these conditions occur, do the following:

1. Power off the printer immediately.

2. Disconnect the power cord from the electrical outlet.

3. Call an authorized service representative.

PPoow

weerr C

Coorrdd SSaaffeettyy IInnffoorrm

maattiioonn

Before operating your printer, read the following instructions carefully. For details, contact your Xerox
representative.

WARNING:

• The electrical supply for the device must meet the requirements stated on the data plate on

the rear of the device. If you are not sure that your electrical supply meets the requirements,
consult your local electricity provider or a licensed electrician.

• Do not use an extension cord.

• Do not remove or modify the power cord.

Refer to these instructions to ensure the continued and safe operation of your printer.

• Use the power cord that is supplied with your printer.

• Plug the power cord directly into a properly grounded electrical outlet. Ensure that each end of the

cord is connected securely. If you do not know if an outlet is grounded, ask an electrician to verify
that the outlet is grounded.

Xerox

®

AltaLink

®

B81XX Series Multifunction Printer

User Guide

13

«
...
11
12
13
14
15
...
»

Summary of Contents for AltaLink B81 Series





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltaLink B81 Series

Brand: Canon Pages: 58

image Prograf iPF680 Series

Brand: Canon Pages: 132

Brand: Canon Pages: 44

imageClass LBP6230dw

Brand: Canon Pages: 16

Brand: Canon Pages: 2

imageprograf IPF785

Brand: Canon Pages: 42

Brand: Canon Pages: 148

Color Bubble Jet BJC-8200

Brand: Canon Pages: 6

Color Bubble Jet BJC-1000 Series

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Color Bubble Jet BJC-8200

Brand: Canon Pages: 105

Brand: Canon Pages: 2

Brand: Canon Pages: 68

Brand: Canon Pages: 4

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands