Xerox 3117 - Phaser B/W Laser Printer Service Manual Download Page 44

Page: 44 / 129

System Overview

Service Manual

3-31

3.4.7 Installing Printer Software

The supplied CD-ROM contains Windows printing software, Linux printing software, on-line User’s Guide and

Acrobat Reader to view the User’s Guide.

1. If you are printing from Windows

- You can install the following printer software using the CD-ROM.

• Printer driver for Windows. Use this driver to take full

- advantage of your printer’s features. For details, see Software User Guide.

• Status Monitor allows you to see the printing status of the printer. For details, see Software User

Guide.

2. If you are printing in Linux

- Go to Software User Guide for information about installing the Linux driver.

3. System Requirements

Your machine supports following operating system.

• Windows 98/Me/2000/XP - The following table shows Windows requirements.

Item

Requirements

Operating System

Window 98/Me/2000/XP

CPU

Window 98/Me/2000/XP

Pentium II 400 or higher

Window XP

Pentium II 933 Ghz or higher

RAM

Window 98/Me/2000

64 MB or higher

Window XP

128 MB or higher

Free Disk Space

Window 98/Me/2000

300 MB or higher

Window XP

1 GB or higher

Internet Explorer

5.0 of higher

Summary of Contents for 3117 - Phaser B/W Laser Printer


































































































































Search results

Summary of Contents for 3117 - Phaser B/W Laser Printer

Reviews:

Brands by name

Popular brands

Xerox 3117 - Phaser B/W Laser Printer, Service Manual

Search results

Summary of Contents for 3117 - Phaser B/W Laser Printer

Reviews:

Brands by name

Popular brands