XDP Recreation G SURF N SWING'IN Series Manual Download Page 35

 

DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. 

CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or [email protected] 

34 

 

 

 

 

PRODUCT INFORMATION & SUPPORT 

 

 

 

 

 

 

 

 

 

 

 

REGISTER YOUR 

“XDP” PURCHASED / PRODUCT 

PLEASE VISIT OUR WEBSITE at www.xdprecreation.com to register your 

Purchased Product using the 

manufacturer date code

 

found near the Warning 

Label on the "TOP BAR"

 of this swing set. 

There also is a 

short on-line survey

 which you can fill out to complete the Product 

Registration:   

http://xdprecreation.com/index.php/product-registration/ 

LIKE US ON FACEBOOK     

    @XDPRECREATION               

https://www.facebook.com/XDPRecreation/ 

VISIT OUR WEBSITE: www.xdprecreation.com

 

 
 

Please Retain Sales Receipt for Warranty Purposes.

 

DO NOT RETURN THE SET TO THE STORE

If replacement parts or

 

IF

 

Customer 

Service is needed

 

please contact 

XDP Recreation

 

by email at [email protected]

 

or

 

CALL 1-866-884-0535

 

between 8:00am and 5:00pm (Eastern Standard Time), Monday - 

Friday.    This Swing Set is designed to be used safely by children, ages 3 years to 8 years, with weight 

capacity of 100 lbs per child. 

This play gym is designed for backyard use only and is NOT intended for playgrounds, schools, day 

care facilities, nurseries or other public places. 

Follow all assembly instructions carefully and as directed in this manual

This gym conforms to all safety requirements by ASTM for Home Playground equipment when properly assembled using 

the instructions enclosed. 

Adult assembly is required. 

Contains small parts. 

 

For proper stability and safety, this gym set should be installed with ground 

anchors. 

IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS 

SET AT OR BY PURCHASING FROM XDP RECREATION'S WEBSITE AT www.xdprecreation.com 

XDP RECREATION LLC, 5910 SHILOH ROAD EAST, SUITE 108, ALPHARETTA, GEORGIA 30005 

Summary of Contents for G SURF N SWING'IN Series





































Reviews: