manualshive.com logo in svg

XCS ULTIMATE 2 SLED, Manual

Share
Download
XCS ULTIMATE 2 SLED Manual Download Page 11

 
BNC

- Standard configuration provides  one HDSDI loop through from top stage up to two available. 

 
0B 306

- Recorder power (user selectable) 4.5, 7.2, 9, 14.4 volts output and video out to recorder. Video 

input to monitor on channel two

. Removed but can be added

 

 

Rear Battery Housing 

The rear battery housing can be moved in and out by loosening the two 10-32 SHCS. There are safety 
stops on the ends so the housi

ng will not slide off the rails. Over 4” of travel, increases your panning 

inertia 

 
Trim  Knobs 

The LEH comes set up with trim knobs on one side, they can be transferred to the other side of the sled 
by loosening the set screw and spinning off the knobs. The left-right drive shaft must be removed and 
reassembled on the opposite side. See 

“Swapping the inching knobs” 

 
Programmable Digital Level Placement  
There are two 4-40 drilled and tapped holes on each side of the LEH. These holes are aligned with the 
XCS PDL housing. The screws should not protrude into the LEH housing any longer than .1875

”. 

 

On Screen  (LCD) Text Messages 

Upon power up, 

the sled’s serial number 

#0000xxx

 and the software revision level are displayed  

rev.2.0

 

Listed here are on screen text messages and causes for the error message.  

BATT 1 CANNOT BE 24 VOLTS

- 24 volt battery connected to wrong battery plate, B3 only. 

BATT 2 CANNOT BE 24 VOLTS

- 24 volt battery connected to wrong battery plate, B3 only. 

    

Above two messages are each shown for a few seconds followed by a shutdown of the sled

. 

 

24V Over Current Cycle Power-

 Over current draw on the system or dead short or more than 36 volt 

input. Turn off power, remove issue, and turn back on. 
 

12V Over Current Cycle Power

- Over current draw on the system or dead short or more than 18 volt 

input.  Turn off power, remove issue, and turn back on. 
 

LEH internal user selectable adjustments

 

 

To access the internal adjustments inside the LEH you first should remove it from the Center 

post.  Remove the six 

3/32” hex head screws holding the housing together. Lift up a few inches and turn it 

over. There will be 6 to 8 wires and 1 or 2 connectors depending on your options connecting the top half 
to bottom half. You now have access to make the following choice of adjustments. 

 
 

9 

Removable  jumpers are used 

to set voltages for 

RECORDER’s  voltage output 

Three battery 

terminal blocks 

Summary of Contents for ULTIMATE 2 SLED















Reviews:

No comments

Brands by name

Popular brands

Load more brands