background image

2.0  INSTALLATION

© 2001 Xantrex Technology Inc.  All Rights Reserved.

P/N  975-0013-01-01 Rev B  10/01

9

Series Stacking (continued)

The STACKING port allows two SW or PS Series inverter/chargers to be used in the same system in a “SERIES”

configuration to operate 240 VAC loads. Series stacking can also be used to connect to 240 VAC only power systems
providing both 120 and 240 VAC outputs. A series stacking interface cable (SWI) is required to connect the series
stacking port of the inverters. In this mode the inverters act independently of each other; however their output is
phase locked and synchronized 180 degrees out-of-phase. Both units can independently charge the batteries or
provide battery backup power during a utility outage. 230 VAC/50 Hz units can not be stacked.

NOTE: Use tape to label the inverters as INVERTER 1 (L1) and INVERTER 2 (L2), for future
reference.

Series Stack DC Wiring (one disconnect device)

When stacking two inverters using one DC disconnect device, connect the units and batteries as follows:

• Tie the inverter’s negative terminals together using an appropriate length of cable (sized to fit).

• Connect one of the inverter’s negative terminals to the negative terminal of the battery bank.

• Tie the inverter’s positive terminals together using an appropriate length of cable (sized to fit).

• Connect one of the inverter’s positive terminals to the DC disconnect.

• Connect the DC disconnect to the positive terminal of the battery bank.

• Connect the Series Stacking Cable (SWI) to the STACKING port of both inverters.

• Connect the DC chassis ground lugs of both inverters together using a heavy gauge wire.

• Connect the negative end of the battery bank to a solid earth ground (refer to inverter installation manual).

NOTE: Connect the positive and negative wires to the batteries as show in the illustration
below. This ensures an even charge and discharge through the battery bank.

Figure 2-3

Series Stacking Using One DC Disconnect (Block Diagram)

+

+

DC

Disconnect

Negative

Tie

Series Stacking

Cable (SWI)

+

+

+

+

Positive

Tie

Inverter 1 (L1)

Inverter 2 (L2)

NOTE: Series Stacking

Cable connects on AC

side for SW inverters

DC Ground

Chassis Ground

Summary of Contents for SWI























Reviews: