background image

12

xPower600 Owner’s Manual

5.4  Interference with Electronic Equipment

5.4.1  Buzzing Sound in Audio Systems

Some inexpensive stereo systems and “boom-boxes” will emit a

buzzing sound from their loudspeakers when operating from the

AC output of xPower600.  This is because the power supply in the

equipment does not adequately filter the modified sine wave

produced by xPower600.  Unless the stereo can be operated

directly from xPower600’s 12 Volt DC Power Socket, the only

solution is a sound system with a higher quality internal power

filter.

5.4.2  Television Interference

xPower600 is shielded to minimize interference with TV signals.

In some cases, particularly with weak TV signals, some interference

may still be visible in the form of scrolling lines across the screen.

In this case, take the following corrective measures:

1. Use an extension cord to position xPower600 as far away as

possible from the television, antenna, and cables.

2. Adjust the orientation of xPower600, television, antenna, and

cables to minimize interference.

3. Maximize TV signal strength by using a better antenna, and

ensure a shielded antenna cable is used.

4. Try a different TV. Different models of TV sets vary greatly in

their susceptibility to interference.

Summary of Contents for PROwatt 600





































Reviews: