background image

7

    PM

 Set Time

Sets the LOCAL TIME, QUIET TIME “BEGIN” or QUIET TIME
“END” according to the selection made by the SELECT switch. To
set a time parameter, select the hour by repeatedly pressing the
SET TIME button until the correct hour light is on.
DEFAULT: LOCAL TIME

Time
Zone

Pressing the TIME ZONE button changes the LOCAL TIME by
cycling through the available time zones. EST (Eastern Standard
Time), CST (Central Standard Time), MST (Mountain Standard
Time), or PST (Pacific Standard Time) are possible. Only one can
be on at a time. Light is on.
DEFAULT:  PST

To Program Local Time (USUALLY NOT REQUIRED)

:

Use the SELECT switch to select LOCAL TIME. Press the TIME
ZONE switch to select the time zone. Press the SET TIME switch
to set the local time hour.

Quiet Time BEGIN (REQUIRED SETTING)

:

Use the SELECT switch and press it until the BEGIN light is on.
Use the SET TIME switch to select the time in hours Quiet Time is
to begin.

Quiet Time END (REQUIRED SETTING)

:

Use the SELECT switch and press it until the END light is on.
Use the SET TIME switch to select the time in hours Quiet Time is
to end.

SELECT changes the time displayed by the
AGS Remote and is used to set the TIME/
HOUR. In LOCAL TIME mode the user can set
the “Time/Hour” display to the local hour. (Min-
utes are preset at the factory and do not require
user adjustment).
DEFAULT: LOCAL TIME

Select

Local

Time
Begin
End

Summary of Contents for AGS





















Reviews: