background image

Model PA435X 

 

Page 11 

 

© 2003 Xantech Corporation 

 

 

Figure 7 – Bridged Mode Connections 

 

Bridged Mode Connections 

     

In general, it is recommended that the BRIDGED mode not be used in multi-room applications where several 
speakers are driven through room volume controls and the like.

   

 
For such applications, use the STEREO mode. Use the BRIDGED mode for single speaker, higher power 
applications, such as in surround sound systems. Use speakers with an impedance rating of 8-Ohms minimum.  
 
To make connections for the BRIDGED mode, follow the steps given before for stereo connections, but with the 
following differences:  
 
1.  You may connect the RCA-type patch cables from the OUTPUT jacks of the driving preamp or other source to 

either the LEFT or the RIGHT input jacks of the bridged pair, as shown in Fig. 6. Do this for just the amplifier pairs 
you wish to run in the bridged mode.  

 

CAUTION

:  Be sure 

Power is OFF

 when connecting or switching the amp into or out of BRIDGED operation. 

 
2.  Slide the MODE switch to the 

BRIDGED

 position.  

  

NOTE

:  Do this only on the amplifier pairs you wish to run in the bridged mode! 

 
3.  Connect one speaker wire pair between the 4-terminal "SPEAKER" connectors on the PA435X and the speakers 

as shown in Fig. 6.  Be sure to use only the two outer terminals marked "+” and "–" on the 4-terminal connector as 
shown on the panel for BRIDGED connections. 

 

 
NOTE: Only 

one speaker

 is connected per amplifier pair in the BRIDGED mode! 

 

Summary of Contents for PA435X





















Reviews: