Page: 74
Model MRC88
© 2003 Xantech Corporation
will turn the zone “OFF”. (Be sure to set the PLAY command for the proper Source Emitter Output.
i.e. Right-click on command in Macro Command List and select Source 1 output)
9. Repeat for all zones and commands as required.
NOTE:
Remember: As in the example above, to make commands accessible no matter which source is
selected, you will need to PUNCH the command (Zone Level).
Command Name
Command Description
Parameter 1
Parameter 2
Zone Power Command
Discrete Power ON or OFF
Zone (1-8) (9-16)
PwrState (On, Off)
Zone Toggle Power Command
Power Toggle Command
Zone (1-8) (9-16)
N/A
Zone Volume Command
Set Volume to preset level
Zone (1-8) (9-16)
VolLevel (0 – 63)
Zone Volume Step Up Command
Increase Volume Setting
Zone (1-8) (9-16)
N/A
Zone Volume Step Down Command
Lower Volume Stetting
Zone (1-8) (9-16)
N/A
Zone Balance Level Command
Set Balance to Preset Setting
Zone (1-8) (9-16)
BalLevel (-15-15)
Zone Balance Step Up Command
Step Balance towards Rt. CH
Zone (1-8) (9-16)
N/A
Zone Balance Step Down Command
Step Balance towards Lt. CH
Zone (1-8) (9-16)
N/A
Zone Treble Level Command
Set Treble to Preset Setting
Zone (1-8) (9-16)
TrebLevel (-14dB-14dB)
Zone Treble Step Up Command
Increase Treble Setting
Zone (1-8) (9-16)
N/A
Zone Treble Step Down Command
Decrease Treble Setting
Zone (1-8) (9-16)
N/A
Zone Bass Level Command
Set Bass to Preset Setting
Zone (1-8) (9-16)
BassLevel (-14dB-14dB)
Zone Bass Step Up Command
Increase Bass Setting
Zone (1-8) (9-16)
N/A
Zone Bass Step Down Command
Decrease Bass Setting
Zone (1-8) (9-16)
N/A
Zone Source Select Command
Select Source for Zone
Zone (1-8) (9-16)
Source (1-8)
Zone Mute State Command
Discrete Mute ON or OFF
Zone (1-8) (9-16)
MuteState (On, Off)
Zone Mute Toggle Command
Mute Toggle Command
Zone (1-8) (9-16)
N/A
Zone Restore Balance Command
Restore Balance to Center
Zone (1-8) (9-16)
N/A
Zone Restore Treble Command
Restore Treble to Flat
Zone (1-8) (9-16)
N/A
Zone Restore Bass Command
Restore Bass to Flat
Zone (1-8) (9-16)
N/A
Zone Start Z Adjust Command
Enter ‘Zone Adjust’ Mode
Zone (1-8) (9-16)
N/A
Zone Set Max V Command
Set Maximum Zone Volume
Zone (1-8) (9-16)
N/A
Zone Adjust Done Command
Exit ‘Zone Adjust’ Mode
Zone (1-8) (9-16)
N/A
Zone Start Trim Adjust Command
Set Source Input Trim Setting
Zone (1-8) (9-16)
N/A
Turn Off All Zones Command
Power All Zones OFF
Zone (1-8) (9-16)
N/A
Set Max On V Command
Set Maximum ON Volume Setting
N/A
N/A
Table 2 – Internal Amplifier Commands
ZONE EXPANSION (CONNECTING MULTIPLE MRC88 CONTROLLERS)
Two MRC88 Controllers can be used to expand the number of zones in a MRC88 system to SIXTEEN. The two
MRC88 System Controllers interface via their
Expansion
port located on the rear of each Controller [
Figure 3-
(30)
].
Connecting two units via their Expansion port, provides for seamless 8 Source / Sixteen Zone operation,
allowing the same Zone Linking, Priority Lockout, and Monitor Lockout features throughout all SIXTEEN zones.
IR Routing is also supported in this mode.
