3
Modules & Connecting Blocks
795-20
Fig. 2
A Typical 795-20 Four Zone System
COMMON EMITTERS
ZONE EMITTERS
A
B
A
B
A
B
A
B
+12V
ZONE 1 ZONE 2 ZONE 3
ZONE 4
ZONE IR INPUTS
ZONE 4
ZONE 3
ZONE 2
ZONE 1
+12 IN G +12 IN G +12 IN G +12 IN G
POWER
10 9 8 7 6 5 4 3 2 1
795-20
FOUR ZONE AMPLIFIED CONNECTING BLOCK
IR
CONFIRM
V V G S
POWER 15VAC
VIDEO
AUDIO
LEFT
INPUT
OUTPUT
AUDIO
RIGHT
1
2
3
4
SYLMAR, CA • MADE IN U.S.A.
®
RP41AV
REMOTE PREAMP
OUT
+12V
IR IN
GND1
GND2
+12V
XANTECH
1 (ON)
0 (OFF)
1 2 3 4 5 6 7 8 910
ON
SENDER/
EMITTER
123456789
1
0
795-20
Four Zone
Amplified
Connecting
Block
Satellite Receiver
VCR 1
MAIN ROOM, EQUIPMENT CABINET, ETC.
283M
Blink-IR™ Mouse Emitter
GND
+12V
ZONE 2
780-80
J-Box
IR Receiver
3-Wire
Cable
GND
+12V
480-00
Dinky Link™
IR Receiver
Red
Stripe
ZONE 3
+12V
IR OUT
GND
780-80
J-BOX RECEIVER
XANTECH
CD Changer
Cassette DecK
Laser Disc
ZONE 1
AV
Receiver
Zone 1
490-00
Series
Micro Link™
IR Receivers
ZONE 4
3-Wire
Cable
IR OUT
GND
+12V
Red
Stripe
VCR 2
To 120 V AC
(u
nswitch
ed)
781RG
Power Supply
283M
Blink IR™
286M
Dual Blink IR™
AV
Receiver
Zone 2
AV
Receiver
Zone 3
Remote Preamp
COMMON
SOURCES
ZONE
EQUIPMENT
3-Conductor Cable
(unshielded OK)
Cable Box
GND
IR OUT
+12V
Smart
Pad
3
™
ST
OUT
V
IR
RCVR
PWR
G
S
Zone 4
AM/FM
Tuner
Zone 4
RP41AV
Makita
Drape Controller
794-60
Interface
Module
+12V
GND
291-10
Hidden Link™
IR Receiver
7 Foot Quick
Connect Cable
CB12
Connecting
Block
X
X
Do Not Use
These Jacks
283M
Blink IR™
283M
Blink IR™
283M
Blink IR™
283M
Blink-IR™ Mouse Emitter
283M
Blink IR™
283M
Blink IR™
283M
Blink IR™
IR OUT
IR OUT
5. The resistors in series with each zone and common emitter port provides current sharing to each
emitter and also allows the use of dual emitters in combination with single emitters. You may,
therefore, connect any combination of the 282, 283, 284 & 286 series emitters to the zone or common
ports (such as that illustrated in
Fig. 2
for the common ports), to control the desired number of
components.
6. If only one emitter is required in any zone, it may be plugged into either the "A" or "B" jack.
7.
CAUTION:
Be sure to use
MS-1
Mouse Emitter Shields with the 282M and 284M series emitters, if
you use them instead of the 283M's & 286M's. The MS-1's will stop the stray IR output of a zone emitter
or a common source emitter from bleeding over into another zone or zones. This is especially
important when zone receivers and source equipment are stacked close to each other.
