XAC FD150 Installation Manual Download Page 2

1.

 

B

EFORE 

S

TARTING 

 

Open  the  gate  behind  the  device  (Figure  1),  and  find  the  power  input  on  the  right  side  of  the 
terminal.  Connect  the  plug  from  the  power  adapter  into  the  power  input  (Figure  2).  Plug  the 
power adapter into a 120-volt electrical outlet or into a surge suppressor (recommended) after the 
power cord is connected to the power adapter. 
   

             

 

Figure 1                                                  Figure 2 

 

 

Operating Temperature: 0 

°

C to 40 

°

 

Modem Speed: V.22bis 2400bps/ V.32bis 14400bps 

 

RTC battery spec. : 3V, CR2032 

Caution: 

Risk of explosion if the battery is replaced by an incorrect type. Please dispose of used battery 

according to the instructions.

   

Warning: 

A  shielded-type  power  cord  is  required  in  order  to  meet  FCC  emission  limits  and  also  to  prevent 

interference  to  the  nearby  radio  and  television  reception.  It  is  essential  that  only  the  supplied  power  cord  be 
used.

 

 
Connect  one  end of  the  phone  cord  into  one  of the jacks  on the  back  of  the  terminal  (Figure 3). 
Plug the other end of the cord into a modular wall jack (Figure 4). Use only a jack for an analog 
line like a fax line or a standard telephone. 

 

                                 

 

Figure 3                                                  Figure 4

 

 

(Optional) This terminal supports three USB ports. Two USB host ports locate on the back of the 
terminal (Figure 5). One USB device port locates on the left side of the terminal (Figure 6). If the 
terminal uses a peripheral device with USB connector, plug it into the USB host port. 

(Optional) This terminal supports one RS-232 ports of RJ-12 offset keyed connector. If the terminal 
uses a peripheral device with this type of connector and interface, plug it into the RS-232 port on 
the back of the terminal (Figure 7).   

(Optional) If the terminal needs communication over Ethernet, plug cable into the RJ-45 port on 
the back of the terminal (Figure 8). 

     

     

     

 

Figure 5                        Figure 6                        Figure 7                          Figure 8 

 

2.

 

P

OWER 

O

N THE 

T

ERMINAL 

 

Plug  the  power  cord  into  the  power  jack  and  plug  the  power  adapter  into  a  120-volt  electrical 
outlet or into a surge suppressor (recommended) after the power cord is connected to the power 
adapter. Press the “Cancel” button at the front of device (Figure 9) until the system is booted up. 

Summary of Contents for FD150






Reviews: