Motion Detection only after Dusk or 24 hours:
This section configures the MS16A to send the ON Command at dusk (no light) and the OFF Command at dawn (any light) for the Unit Code one number higher than the
current Unit Code setting (i.e., MS16A set to A1 will control A2 when dawn/dusk is detected). When battery power is initially applied to the MS16A, this feature is disabled.
This section also configures the MS16A to detect motion at all times or only at night. The default setting is to detect motion at all times.
1.
Press the UNIT/OFF button once.
2.
The red LED flashes.
3.
Press and hold the HOUSE/ON button.
4.
The green LED (located behind the sensor window) turns on the following:
5.
A few seconds later, the MS16A reports its current setting. Release the button. The number of blinks reported by the MS16A represent the following:
6.
If you do not wish to change the current setting, take no further action at this point. A few seconds later, the MS16A will timeout. The MS16A will indicate this to you by
displaying a sustained blink (slightly longer than the report blinks).
7.
To change the current setting, first select the Dawn/Dusk and Motion Detection settings you wish to use from the chart above and remember the blink value listed to the
left of them (i.e. for dawn/dusk detection enabled and detect motion only at night there are 4 blinks). Determine the setting you wish to use before starting the
programming procedure because the MS16A will only wait a few seconds after it has finished reporting its current setting for you to begin entering the new setting.
8.
Press the HOUSE/ON button the number of times equal to the blink value in the chart above. Hold the button down on the last press (i.e. for a setting of dawn/dusk
detection enabled and detect motion only at night, press the HOUSE/ON button 4 times and hold on the last press).
9.
A few seconds later, the red LED will blink the new setting.
10. If the programming fails, the red LED will display a sustained blink (slightly longer than the report blinks). This can occur if you wait too long to start your programming,
you press the button more than 2 times, or you press the UNIT/OFF button. If the programming procedure fails, you must start the procedure over.
Delay after Motion before an OFF command is sent:
When no motion is detected, the default amount of time that will pass before the OFF Command is transmitted is Analog; i.e., the setting on the Top Dial (under the rubber
plug on the top of the MS16A). The dial adjusts the delay range from 1 minute to 60 minutes. The following procedure allows you to alter this setting.
1.
Press the House button once, the Red LED flashes.
2.
Press and hold the Unit button, the Green LED turns ON. 3 seconds later, the Red LED will report the setting as follows: -1 blink for Analog Dial 1-60 Mins. -6 blinks for
32 minutes. -2 blinks for 2 minutes. -7 blinks for 64 minutes. -3 blinks for 4 minutes. -8 blinks for 128 minutes. -4 blinks for 8 minutes. -9 blinks for 256 minutes. -5 blinks
for 16 minutes.
Note:
When the setting is 2 blinks or higher, the dial on top of the MS16A is disabled.
3.
If you do not wish to change the current setting, take no further action at this point. A few seconds later, the MS16A will timeout. The MS16A will indicate this to you by
displaying a sustained blink (slightly longer than the report blinks).
4.
To change the current setting, first select the delay time you wish to use from the chart above and remember the blink value listed to the left of it
(i.e. for 64 minutes there are 7 blinks). Determine the time you wish to use before starting the programming procedure because the MS16A will only wait a few seconds
after it has finished reporting its current setting for you to begin entering the new setting.
5.
Press the UNIT/OFF button the number of times equal to the blink value in the chart above. Hold the button down on the last press (i.e. for a setting of 64 minutes, press
the UNIT/OFF button 7 times and hold on the last press).
6.
A few seconds later, the red LED will blink the new setting.
7.
If the programming fails, the red LED will display a sustained blink (slightly longer than the report blinks). This can occur if you wait too long to start your programming,
you press the button more than 2 times, or you press the HOUSE/ON button. If the programming procedure fails, you must start the procedure over.
Sensor Detection vs. Direction of Motion
For best detection results, mount the MS16A so the person entering the area will cut across the MS16A's field of view. Do not mount the PMS 03 near hot or cold sources (i.e.
heat vents, air conditioners, direct or reflected sunlight) as this may cause false triggering of the MS16A. Sensor's fields of view are 90 Degrees Horizontally, 30 Degrees
Vertically and detection range is approximately 20Ft.
DEFAULTS:
After replacing batteries, please wait 30 seconds before the MS16A will see any motion. After transmission, you need to wait 10 seconds before the MS16A will see motion
again. The default House & Unit Codes for Motion Detection is: "A1" ON.
The default for Motion Detection is: detect at all times (24 HOUR).
The default for Time Out, that "A1" OFF is sent is: 1 minute.
The default House/Unit Codes for Dusk/Dawn, is: "A2" ON at Dusk, "A2" OFF at Dawn.
Note: As with all RF transmitter devices; electrical fields, metal doors or door window frames and appliances can cause interference that can decrease the strength of the
transmitted signal. Re-locating the TM751 RF Base Transceiver may increase your ability to receive the necessary X10 Signals from the MS16A.
30 DAY LIMITED WARRANTY x10pro-usa.com (X10PRO-USA), a division of Authinx Inc., warrants this product to be free from defective material and
workmanship for a period of 30 days from the original date of purchase at retail. X10PRO-USA agrees to repair or replace, at its sole discretion, a defective
product if returned to X10PRO-USA within the warranty period and with proof of purchase. If service is required under this warranty:
Call 1-888-384-0969, visit
www.x10pro-usa.com
, or email
Blinks
1
Dawn/Dusk
Disabled
Motion Detection
Day & Night
2
Disabled
Night Only
3
Enabled
Day & Night
4
Enabled
Night Only
