background image

3

1. Specification and features

Model: ARES

Dimension: Height x Width x Length (93mmx48mmx32mm)

Weight: 165g

Body Material: Zinc Alloy + Aluminium Alloy

Atomizers Connector:

Stainless Steel 510 Connection, Nickel Plated Brass Contact

Display: 1.3 OLED

Support both dual 18650 or dual 20700 Li-On Battery

Atomizers

o

Output power range: 5W ~ 220W

o

Maximum 40A continuous current.

o

Output voltage range: 0.5V ~ 15.5V (Buck-Boost DC-DC converter)

Power consumption (Without fire): 0.4W

Very low standby current: 39.5uA (Able to standby 3.9 years for fully charge battery)

Coil resistance

o

Measurement range 0.04Ohm ~ 10Ohm

o

Resolution: 1m Ohm (based on 0.1ohm measurement)

Power control mode

o

Recommended resistance range: 0.08Ohm~3Ohm

o

Coil over heat protection. Refer to coil material table for detail.

Temperature control mode

o

Recommended resistance range: 0.08Ohm~2Ohm

o

Repeatability: 1 degree Celsius / 1.8 Fahrenheit

o

Support Ni-200, Ti 01/02, SS316L, NiFe30, NiFe70. Refer to coil material table for

detail.

o

Temperature adjustment range can be change through “X-Taste Advance”.

o

Dry coil protection.

Power control / Temperature control mode

Battery Management

o

Support maximum up to 2A USB charging current.

o

Support cell by cell monitoring

o

Support cell balancing: 99.5%

Summary of Contents for ARES



























Reviews: