I
I
ASSEMBLY INSTRUCTIONS
XSFP456 PATRON
STOP NOW!
It will be necessary to use the climbing belt with your full-body fall arrest harness
while ascending the tree and attaching your treestand. As you climb it will be necessary to
slide the climbing belt up the tree. Once you've reached the desired height and your
treestand is properly secured to the tree, you will need to attach the permanent tree belt
and secure tether strap as illustrated on page 5 of this manual. FAILURE TO WEAR YOUR
FULL-BODY FALL ARREST HARNESS AT ALL TIMES WHILE USING THIS PRODUCT
MAY RESULT IN SERIOUS INJURY OR DEATH!
WARNING!
Prior to installing your X-Stand hang-on treestand, you must install a climbing
system (i.e., stacking sticks, ladders, sectionals, etc.) which meets or exceeds ASTM
standards. Failure to follow these instructions may result in serious injury or death!
�
WARNING!
DO NOT attempt to install this product on a tree that is not straight, healthy,
and devoid of dead branches, limbs, vines, or anything that might interfere with the
installation. DO NOT attempt to install this treestand on a tree that is leaning, diseased,
crooked, has loose bark, or does not meet the minimum installation diameter of nine (9)
inches (23 cm) at
treestand height (i.e. seating platform height) or exceeds the maximum
installation diameter of twenty (20) inches (51cm) at treestand height (i.e. seating platform
height).
Failure to follow these instructions may result in injury or death!
Assembly Instructions for the Patron
Step 1. Attach the rear frame support to the plat
form using two (2) 5/16" x 1-3/4" Hex Bolts {C}
eight (8) nylon washers and two (2) 5/16" nylock
nuts tighten securely.
Step 2. Securely fasten each of the two plastic
coated cables to the foot platform using two (2)
5/16" x 1-3/4"" hex bolts {C} six (6) nylon washers
and two (2) 5/16" nylock nuts.
Step 3. Securely fasten the other two ends of the
plastic coated cables one on each side of the rear
frame support using two (2) 5/16" x 2" hex bolts {B}
six (6) nylon washers and two (2) 5/16" nylock nuts
as seen in Fig. 1
Step 4. Securely fasten the seat and backrest as
sembly to the top of the rear frame support using
two (2) 5/16" x 2" hex bolts {B} ten (10) nylon wash
ers and two (2) 5/16" nylock nuts.
Step 5. Securely fasten the armrests to the seat
support using four (4)¼" x 2¼" hex bolts {D} ten
(10) nylon washers, two (2) 1/4" nylon spacers
(Front) {G} and four (4)¼" nylock nuts.
Step 6. Securely attach the rear connecting tube
to the rear frame support using three (3)¼" x 1
1
左" hex bolts {
K
} six (6) nylon washers and three
(3)¼" nylock nuts.
Step 7. Securely attach the tension bars by in
serting it into place using two (2)¼" x 1怜" hex
bolts {A} four (4) nylon washers and two (2)¼"
nylock nuts. Recheck every nut and bolt at this
time for tightness.
Step 8. Adjust seat and backrest tension by turn
ing the allen bolt {E} counter clockwise until de
sired tension is archived.
10
I READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with ASTM F2 7 23 Standard Practice for Tree stand Instruction.
