background image

C i 5 1 / C i 5 2   S P E C T R O P H O T O M E T E R  

2

 

Proprietary Notice 

The information contained in this manual is copyrighted information proprietary to X-Rite, 
Incorporated.  
Publication of this information does not imply any rights to reproduce or use it for purposes other 
than installing, operating, or maintaining this instrument described herein. No part of this manual 
may be reproduced, transcribed or translated into any language or computer language in any 
form or by any means: electronic, magnetic, mechanical, optical, manual, or otherwise; without 
the prior written permission of an authorized officer of X-Rite, Incorporated. 
Patents: www.xrite.com/ip 
“© 2017, X-Rite, Incorporated. All rights reserved” 
 

X-Rite® is a registered trademark of X-Rite, Incorporated. All other logos, brand names, and product names mentioned are the properties 
of their respective holders. 

Warranty Information 

X-Rite, Incorporated (“X-Rite”) warrants each instrument manufactured to be free of defects in 
material and workmanship for a period of 12 months*. This warranty shall be fulfilled by the 
repair or replacement, at the option of X-Rite, of any part or parts, free of charge including labor, 
F.O.B. its factory or authorized service center. 
X-Rite warrants this Product against defects in material and workmanship for a period of twelve 
(12) months from the date of shipment from X-Rite’s facility, unless mandatory law provides for 
longer periods.  During such time, X-Rite will either replace or repair at its discretion defective 
parts free of charge.  
 
X-Rite’s warranties herein do not cover failure of warranted goods resulting from:  (i) damage 
after shipment, accident, abuse, misuse, neglect, alteration or any other use not in accordance 
with X-Rite’s recommendations, accompanying documentation, published specifications, and 
standard industry practice; (ii) using the device in an operating environment outside the 
recommended specifications or failure to follow the maintenance procedures in X-Rite’s 
accompanying documentation or published specifications; (iii) repair or service by anyone other 
than X-Rite or its authorized representatives; (iv) the failure of the warranted goods caused by 
use of any parts or consumables not manufactured, distributed, or approved by X-Rite; (v) any 
attachments or modifications to the warranted goods that are not manufactured, distributed or 
approved by X-Rite.  Consumable parts and Product cleaning are also not covered by the 
warranty. 
 
X-Rite‘s sole and exclusive obligation for breach of the above warranties shall be the repair or 
replacement of any part, without charge, which within the warranty period is proven to X-Rite‘s 
reasonable satisfaction to have been defective.  Repairs or replacement by X-Rite shall not revive 
an otherwise expired warranty, nor shall the same extend the duration of a warranty.  
 
Customer shall be responsible for packaging and shipping the defective product to the service 
center designated by X-Rite.  X-Rite shall pay for the return of the product to Customer if the 
shipment is to a location within the region in which the X-Rite service center is located. Customer 
shall be responsible for paying all shipping charges, duties, taxes, and any other charges for 
products returned to any other locations.  Proof of purchase in the form of a bill of sale or 
receipted invoice which is evidence that the unit is within the Warranty period must be presented 
to obtain warranty service.  Do not try to dismantle the Product.  Unauthorized dismantling of the 

Summary of Contents for Ci51
























Reviews: