Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in this
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
HDMI Wiring
IMPORTANT! HDMI Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference can have an adverse effect on HDMI
transmission limiting performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
• WyreStorm recommends using high quality HDMI cables such as WyreStorm Express to ensure the highest content performance available.
• The length of HDMI cable used can restrict the available video resolution. See
Video Resolutions
in the
table before determining cable length.
EDID Settings
EDIDs can be configured to resolve issues with video output on displays that may not accept the maximum resolution available from the source.
Note:
This product was released in multiple versions which have different EDID settings for the rotary switch. See Identifying Product Versions to ensure that
the proper settings are used based on the product version.
• Ensure that a display is connected and powered On to the selected output before copying EDIDs or the copy will fail. When this occurs, EDID will be set to
1080p @60Hz 2ch.
• Power to the splitter must be cycled (Off/On) after changing dip switches in order for the setting to take effect.
EDID Dial Setting Location
Copying EDIDs from Output 1
1. Set the EDID dial to 0 (Default)
2. Connect a source to the input.
3. Connect the lowest resolution display to output 1.
4. Power on the source, display, and splitter.
5. After a few moments the EDID from the display will be configured.
Note:
If the EDID copy fails, the EDID will be set to 1080p @60Hz 2ch.
Copyright © 2017 WyreStorm Technologies |
SP-0104-H2 Quickstart Guide | 171115
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
1 of 4
Operation
Rotary Position
Copy EDID from HDMI output1 (default setting)
0
1920x1080i @60Hz 2ch
1
1920x1080i @60Hz 5.1ch
2
1920x1080i @60Hz 7.1ch
3
1920x1080p @60Hz 2ch
4
1920x1080p @60Hz 5.1ch
5
1920x1080p @60Hz 7.1ch
6
1920x1080p @60Hz 3D 2ch
7
1920x1080p @60Hz 3D 5.1ch
8
1920x1080p @60Hz 3D 7.1ch
9
1280x1024 DVI
A
1920x1080 DVI
B
1920x1200 DVI
C
3840x2160p @30Hz 2ch
D
4096x2160p @60Hz 2ch
E
Copy EDID from HDMI output2
F
Version 1 and 2 Rotary Dial Settings
Mode
Operation
Rotary Position
Mixed
Video: Compatibility | Audio: Compatibility (Default) 0
Video: Quality | Audio: Compatibility
1
Video: Compatibility | Audio: Quality
2
Video: Quality | Audio: Quality
3
Fixed
3840x2160p @30Hz 2ch
4
3840x2160p @30Hz 5.1ch
5
3840x2160p @30Hz 7.1ch
6
1920x1080p @60Hz 3D 2ch
7
1920x1080p @60Hz 3D 5.1ch
8
1920x 1080p @60Hz 3D 7.1ch
9
Copy
Copy EDID from Output 1
A
No Function
B~F
Version 3 Rotary Dial Settings
