Wren 150 WALL Assembly Manual Download Page 10

Page: 10 / 12

WALL/SHALLOW

BASE UNIT

150 - 600
WALL/SHALLOW BASE

Assembly Guide

For Internal Use: FI.WR.INS.034_WKIN00124_MULTI_150-600_WALL_ShallowBASE_Rev6.indd

Page 9

Step 25.

Insert hinge in top & bottom
holes as shown.

Step 26.

Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.

Step 27.

Attach the door to unit
where required.

To attach door
clip hinge onto hinge
plate and click to secure.

adjust

hinge using a screw

driver, tighten or loosen as
required at points

Point

- In - OUT

Point

-Left - Right

FRONTAL HINGE
ADJUSTMENT

The top and bottom

hinges

MUST

adjusted to the

SAME

STRENGTH.

Release

door

Pull catch as shown,
to release hinge
from the hinge plate.

View from Inside of Carcass

Hinge Plates

Step 28.

Adjust hinge to suit. As shown below.

Hinge Cover Caps

Step 29.

Fit cover caps to hinge.
Adjust Softclose to suit.

Summary of Contents for 150 WALL













Search results

Summary of Contents for 150 WALL

Reviews:

Related manuals for 150 WALL

Brands by name

Popular brands

Wren 150 WALL, Assembly Manual

Search results

Summary of Contents for 150 WALL

Reviews:

Related manuals for 150 WALL

Brands by name

Popular brands