manualshive.com logo in svg

Wren Kitchens Vogue BASE UNIT 700 2 Door, Assembly Manual, Page: 7 / 8

Share
Download
Wren Kitchens Vogue BASE UNIT 700 2 Door Assembly Manual Download Page 7

Page 6

For Internal Use: FI.WR.INS.021_WKIN00103_BASE_700-800_2Dr_Rev6.indd

Step 12.

Insert hinge in top & bottom 

holes as shown below. 

Step 13.

Secure hinges by tightening 
2 x screws with hinge dowels 
attached. These are already 
positioned within the hinges.

Step 14.

Attach the door to unit 

where required. 

To attach door, clip hinge 
onto hinge plate and click 
to secure.

Hinge Cover Caps

Step 16.

Fit cover caps to hinge. 
Adjust Soft close to suit.

Step 15.

Adjust hinge to suit. As shown below.

To 

adjust

 hinge using 

a screw driver, tighten 

or loosen as required at 

points 

1

 & 

2

.

Point 

1

 - In - Out 

Point 

2

 - Left - Right

1

2

FRONTAL 
HINGE 
ADJUSTMENT

Hinge Plates

View from inside of unit

To 

release

 door,

pull catch as shown,
to release hinge from 
the hinge plate.

The top and bottom 

hinges 

MUST

 be 

adjusted to the 

SAME 

STRENGTH.

To 

Move

 the 

hinge up/down, 
loosen screws 
A + B, 
Manoeuvre 
the door, then 
re-tighten the 
screws

A

B

Summary of Contents for Vogue BASE UNIT 700 2 Door









Reviews:

No comments