background image

 

4K 4x4 HDMI2.0 Matrix Switcher

 

 

Preface 

Read this user manual carefully before using the product. Pictures shown in this 
manual is for reference only. Different models and specifications are subject to real 
product. 

This manual is only for operation instruction only. The functions described in this 
version are updated till December 11, 2016. In the constant effort to improve our 
product, we reserve the right to make functions or parameters changes without notice 
or obligation. Please refer to the dealers for the latest details. 

 

FCC Statement 

This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. It has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a commercial 
installation.   

Operation of this equipment in a residential area is likely to cause interference, in which 
case the user at their own expense will be required to take whatever measures may be 
necessary to correct the interference 

Any changes or modifications not expressly approved by the manufacture would void 
the user’s authority to operate the equipment. 

                   

                   

 

 
 

Summary of Contents for MUH44A-H2











































Reviews: