www.woundwo.com
6
NEHER INSECT SCREENS
Security-relevant fitting parts such as rotary belts, wheels, spring pins and angle brackets must be regularly checked for tightness and
wear. Fastening screws must be tightened if required. All moving parts of the fittings of your Neher element are low-maintenance.
But a little acid-free oil and grease, keep the mechanics running smoothly and ensure ease of use over a long period.
We recommend a maintenance frequency of at least once a year for a tenter frame and at least twice a year for revolving doors. In
particular, the curved spinning band pins have to be lubricated at least twice a year to prevent squeaking. With opposite brush seals, it
may happen at the beginning that the door closes slightly at an angle until the brushes have adapted to each other.
Security-relevant fitting parts such as screws, bed parts and Z-rails must be regularly checked for tightness and wear. Fastening
screws must be tightened if required.
10. FITTING PARTS
11. MOUNTING
The transparent, UV-protected and step-safe polycarbonate panel is weather-resistant, does not become brittle and does not yellow
as quickly as unprotected plates. Depending on the weather, condensation or „stagnant water“ may form on the polycarbonate plate.
This basically represents no problem for the panel. However, the danger of „moss formation“ exists. Depending on your needs, you can
find a remedy with the moss and algae annihilator from Neher or a similar commercial product. Please make sure that only a moss
and algae annihilator may be used which is expressly approved for use on plastic panels.
12. POLYCARBONATE PANEL
www.woundwo.com
6
NEHER INSECT SCREENS
Application Notes
for Neher insect screens
©
Neher
Insektenschutz 04/2019
Changes reserved
8/8
Fitting parts
5
Mounting
6
Security-relevant fitting parts such as rotary belts, wheels, spring pins and angle brackets must be regularly checked for tightness
and wear. Fastening screws must be tightened if required. All moving parts of the fittings of your Neher element are low-mainte-
nance.
But a little acid-free oil and grease, keep the mechanics running smoothly and ensure ease of use over a long period.
We recommend a maintenance frequency of at least once a year for a tenter frame and at least twice a year for revolving doors.
In particular, the curved spinning band pins have to be lubricated at least twice a year to prevent squeaking. With opposite brush
seals, it may happen at the beginning that the door closes slightly at an angle until the brushes have adapted to each other.
Polycarbonate panel
7
Security-relevant fitting parts such as screws, bed parts and Z-rails must be regularly checked for tightness and wear. Fastening
screws must be tightened if required.
The transparent, UV-protected and step-safe polycarbonate panel is weather-resistant, does not become brittle and does not yel-
low as quickly as unprotected plates. Depending on the weather, condensation or „stagnant water“ may form on the polycarbonate
plate. This basically represents no problem for the panel. However, the danger of „moss formation“ exists. Depending on your
needs, you can find a remedy with the moss and algae annihilator from Neher or a similar commercial product.
Please make sure that only a moss and algae annihilator may be used which is expressly approved for use on plastic panels.
Declaration of performance
8
1 ref.no. declaration of performance
2 designation of type
3 level of total energy passage
4 class of wind resistance
NEHER Systeme GmbH & Co. KG
Wellendingerstr. 15
D - 78665 Frittlingen
15
EN 13561
exterior usage
1
RO5-2017-1
SD-2016-1
SP-2016-1
ST-2016-1
PL-2017-1
2
RO5/XX
SDX/XX
SPX/XX
STX/XX
PL/XX
3
„NPD“
„NPD“
„NPD“
„NPD“
„NPD“
4
0
0
0
0
0
1
DF-2016-1
DT-2016-1
LI-2016-1
PT-2017-1
RO4/RO6-2017-1
2
DFX/XX
DTX/XX
LIX/XX
PTX/XX
ROX/XX
3
„NPD“
„NPD“
„NPD“
„NPD“
„NPD“
4
0
0
0
0
1
13. DECLARATION OF PERFORMANCE
