Worx WX530, Safety And Operating Manual

Page: 13 / 16

13
Cordless Circular Saw WX530 WX530.X
Bevel cuts
NOTE: Bevel cutting can’t be used
under EXACTRACK
TM mode.
See Fig. G
Sawdust Removal See Fig. H
EXACTRACK TM
What is EXACTRACK
TM
?
EXACTRACK
TM
is an innovative function, which can help
to make a straight cut easier by keeping the blade flush
against the cutting guide board.
Safety notes
WARNING: Blade is sharp. Always wear
protective gloves.
Keep your hands off from the lower blade guard after
opening the lower blade guard.
EXACTRACK
TM
operation scope
1. EXACTRACK TM operates between 0~43mm in depth. (See
Fig. I)
2. EXACTRACK
TM
works only with 90 degree cut, it does not
work with any angle of bevel cut.
Before operation
WARNING: Make sure battery is not installed
prior to making any adjustments to the saw,
and please place the battery pack nearby the saw.
1. Adjust the desired cutting depth (range 0~43mm).
(See Fig. I)
2. Turn the lever to EXACTRACK TM mode. (See Fig. J)
3. Mark the desired cut line on the workpiece, then clamp
the cutting guide board (not supplied) to make the
board edge right on the cut line, the length of the
cutting guide board should leave 230mm longer at the
both ends. (See Fig. K1)
4. Place the EXACTRACK TM sub-base plate (red part) on
the top of cutting guide board (not supplied), and
ensure the main-base plate is sitting on the workpiece.
(See Fig. K2)
5. Open the lower blade guard manually ( keep
your hands off the blade ), push the saw against the
side of the cutting guide board, then release the hand
off the lower blade guard. (See Fig. K3)
Operation
1. Install the battery.
2. Please hold the saw firmly with both hands and make
sure the main base plate fits securely against the
cutting guide board (not supplied) during cutting. (See
Fig. K4)
3. Switch on the tool to start cutting (See Fig. K5)
STANDARD Mode
For regular 90 degree or bevel cutting (disable
EXACTRACK
TM fucntion), turn the lever to STANDARD mode
and then your tool can be used as a standard circular saw.
(See Fig. L)
The STANDARD mode can be used in the cutting depth of
0~55mm (90 degree), 0~39mm (45 degree).
For product information, go to www.worx.com and
see How To video.
WORKING TIPS FOR YOUR
TOOL
If your power tool becomes too hot, please run your
circular saw no load for 2-3 minutes to cool the motor.
Avoid prolonged usage at very low speeds.
Protect saw blades against impact and shock. Do not force
the tool. Apply light and continuous pressure in order to
avoid overheating the blade tips. Cutting with extreme
force can significantly reduces the performance capability
of the tool and reduces the service life of the saw
blade. Sawing performance and cutting quality depend
essentially on the condition and the tooth count of the saw
blade. Therefore, use only sharp saw blades that are suited
for the material being cut.
Choice of blades: 24 teeth for general work, approx. 40
teeth for finer cuts, more than 40 teeth for very fine cuts
into delicate surfaces, cement board, etc.
Only use saw blades recommended.
MAINTAIN TOOLS WITH CARE
Remove the battery before carrying out any
adjustment, servicing or maintenance.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Your power tool requires no
additional lubrication or maintenance. There are no user
serviceable parts in your power tool. Never use water or
chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry
place. Keep the motor ventilation slots clean. Keep all
working controls free of dust.
Periodically clear dust and chips from guard and base to
ensure proper performance.
FOR BATTERY TOOLS
The ambient temperature range for tool and battery use
and storage is 0
O C-45 O C.
The recommended ambient temperature range for the
charging system during charging is 0
O C-40 O C.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed of
with household waste. Please recycle where
facilities exist. Check with your
local
authorities or retailer for recycling advice.