20V Lithium-Ion Cordless Circular Saw EN
14
and cause loss of control or kickback.
e) Do not attach a saw chain,
woodcarving blade, segmented
diamond wheel with a peripheral
gap greater than 10 mm or toothed
saw blade.
Such blades create frequent
kickback and loss of control.
f) Do not “jam” the wheel or apply
excessive pressure. Do not attempt
to make an excessive depth of cut.
Overstressing the wheel increases the
loading and susceptibility to twisting or
binding of the wheel in the cut and the
possibility of kickback or wheel breakage.
g) When wheel is binding or when
interrupting a cut for any reason,
switch off the power tool and hold
the power tool motionless until the
wheel Comes to a complete stop.
Never attempt to remove the wheel
from the cut while the wheel is in
motion otherwise kickback may occur.
lnvestigate and take corrective action to
eliminate the cause of wheel binding.
h) Do not restart the cutting operation
in the workpiece. Let the wheel reach
full speed and carefully re-enter the
cut.
The wheel may bind, walk up or
kickback if the power tool is restarted in the
workpiece.
i) Support panels or any oversized
workpiece to minimize the risk of
wheel pinching and kickback.
Large
workpieces tend to sag under their own
weight. Supports must be placed under the
workpiece near the line of cut and near the
edge of the workpiece on both sides of the
wheel.
j) Use extra caution when making a
“pocket cut” into existing walls or
other blind areas.
The protruding wheel
may cut gas or water pipes, electrical
wiring or objects that can cause kickback.
GENERAL SAFETY
WARNINGS FOR YOUR
LASER
WARNING: Read all safety warnings
and all instructions.
Failure to follow
the warnings and instructions may result in
serious injury.
Save all warnings and instructions for
future reference.
These lasers do not normally present an
optical hazard although staring at the beam
may cause flash blindness.
Do not stare directly at the laser beam. A
hazard may exist if you deliberately stare into
the beam, please observe all safety rules as
follows:
1. The laser shall be used and maintained
in accordance with the manufacturer’s
instructions.
2. Never aim the beam at any person or an
object other than the work piece.
3. The laser beam shall not be deliberately
aimed at another person and shall be
prevented from being directed towards
the eye of a person for longer than 0.25
seconds area.
4. Always ensure the laser beam is aimed
at a sturdy work piece without reflective
surfaces, e.g. wood or rough-coated
surfaces are acceptable. Bright shiny
reflective sheet steel or similar is not
suitable for laser applications as the
reflective surface may direct the laser beam
back at the operator.
5. Do not change the laser device with a
different type. The manufacturer or an
authorized agent must carry out repairs.
6.
CAUTION:
Use of controls or adjustments
other than those specified herein may
result in hazardous radiation exposure.
ADDITIONAL SAFETY
WARNING FOR CLASS 2
LASER
The laser device fitted to this tool is CLASS
2 with a maximum radiation of 1.5mW and
650nm wavelength.
CLASS 2 LASER RADIATION, DO NOT
STARE INTO BEAM
Summary of Contents for WX523 WorxSaw
