Worx WX437 Safety And Operating Manual Download Page 15

15

Compact Circular Saw

WX437 

WX437.X

OPERATING INSTRUCTIONS

NOTE: 

Before using the tool, read the instruction 

book carefully.

INTENDED USE:

The tool is intended for ripping and cross-cutting wood and 
other materials in straight cutting lines, while resting firmly 
on the work piece.

ASSEMBLY AND OPERATION

Action Figure

Mounting and Removing the Blade

NOTE: 

Lock or loose the blade bolt, 

the spindle lock button should be 
pressed.

WARNING: 

Always remove 

the battery before changing 

the blade!

See Fig. A

Safety switch and On/Off trigger

WARNING

: To avoid cutting 

injury from the sharp blade, 

please don’t put your hands around 
the Base Plate.

NOTE:

 Keep the dust adapter 

connected to dust collecting device 
when using the tool.

See Fig. B

Rip and Cross Cutting

NOTE

: The cutting line of saw blade 

is aligned with the cutting mark 0°.

See Fig. C1, C2

Using the Laser Light Feature

See Fig. D1, D2

Replacing Laser Batteries

See Fig.E1, 
E2,E3

Parallel Guide

See Fig. F1, F2

Adjusting the Cutting Depth

See Fig. G1, G2

Adjusting the Cutting Angle

NOTE: 

The cutting line of saw blade 

is aligned with the cutting mark 45°.

See Fig. H

Pocket cutting

See Fig. I1, I2

Sawdust Removal

See Fig. J

WORKING HINTS FOR YOUR 
TOOL

If your power tool becomes too hot, please run your 
circular saw no load for 2-3 minutes to cool the motor. 
Avoid prolonged usage at very low speeds.
Protect saw blades against impact and shock. Cutting with 
extreme force can significantly reduces the performance 
capability of the tool and reduces the service life of the 

saw blade. Sawing performance and cutting quality 
depend essentially on the condition and the tooth count of 
the saw blade. Therefore, use only sharp saw blades that 
are suited for the material being cut.
Choice of blades: 24 teeth for general work, approx. 40 
teeth for finer cuts, more than 40 teeth for very fine cuts 
into delicate surfaces, diamond for tile, cement board, etc.
Only use saw blades recommended.

MAINTAIN TOOLS WITH CARE 

Remove the plug from the socket before carrying out 
any adjustment, servicing or maintenance.

Keep tools sharp and clean for better and safer 
performance. Follow instructions for lubricating and 
changing accessories. Inspect tool cords periodically and 
if damaged, have repaired by authorized service facility. 
Your power tool requires no additional lubrication or 
maintenance. There are no user serviceable parts in your 
power tool. Never use water or chemical cleaners to clean 
your power tool. Wipe clean with a dry cloth. Always store 
your power tool in a dry place. Keep the motor ventilation 
slots clean. Keep all working controls free of dust. 
If the supply cord is damaged, it must be replaced by 
the manufacturer, its service agent or similarly qualified 
persons in order to avoid a hazard.
Periodically clear dust and chips from guard and base to 
ensure proper performance.

ENVIRONMENTAL 
PROTECTION

Waste electrical products must not be disposed 
of with household waste. Please recycle where 
facilities exist. Check with your local authorities or 

retailer for recycling advice.

Summary of Contents for WX437





















Reviews: