background image

Rotary hammer 

WX338

WORKING HINTS FOR YOUR 

DRILL (HAMMER)

If your power tool becomes over heated, set 

the speed to maximum and run no load for 2-3 

minutes to cool the motor. SDS-plus tungsten 

carbide drill bits should always be used for 

concrete and masonry. 

When drilling in metal, only use HSS drill bits 

in good condition. Where possible use a pilot 

hole before drilling a large diameter hole.

MAINTENANcE

Remove the plug from the socket before 

carrying out any adjustment, servicing or 

maintenance.

There are no user serviceable parts in your 

power tool. Never use water or chemical 

cleaners to clean your power tool. Wipe clean 

with a dry cloth. Always store your power tool 

in a dry place. Keep the motor ventilation slots 

clean. Keep all working controls free of dust. 

Occasionally you may see sparks through the 

ventilation slots. This is normal and will not 

damage your power tool.                                  

If the supply cord is damaged, it must be 

replaced by the manufacturer, its service 

agent or similarly qualified persons in order to 

avoid a hazard.

ENVIRONMENTAL 

PROTEcTION

Waste electrical products should not 
be disposed of with household waste. 
Please recycle where facilities exist. 

Check with your Local Authority or retailer for 
recycling advice.

PLUG REPLAcEMENT 

(UK & IRELAND ONLY)

If you need to replace the fitted plug then 

follow the instructions below.

IMPORTANT

The wires in the mains lead are colored in 

accordance with the following code:

Blue = Neutral

Brown = Live

As the colors of the wires in the mains lead of 

this appliance may not correspond with the 

colored markings identifying the terminals 

in your plug, proceed as follows. The wire 

which is colored blue must be connected to 

the terminal which is marked with N. The wire 

which is colored brown must be connected to 

the terminal which is marked with L.

WARNING:

 Never connect live or 

neutral wires to the earth terminal of the 

plug. Only fit an approved 13A BS1363/A plug 

and the correct rated fuse.

NOTE:

 If a moulded plug is fitted and has to 

be removed take great care in disposing of the 

plug and severed cable, it must be destroyed 
to prevent engaging into a socket.

Connect

Blue to N

(neutral)

Outer sleeve

firmly clamped

Cable grip

Brown L (live)

13 Amp fuse approved
to BS1362

Summary of Contents for WX338













Reviews: