Worx WU427.1 Safety And Operating Manual Download Page 14

14

OpERATINg INSTRuCTIONS

note: 

Before using the tool, read the 

instruction book carefully.

InTEnDED USE:

The tool is intended for ripping and cross-cutting 
wood and other materials in straight cutting lines, 
while resting firmly on the work piece.

ASSEMBLy AND OpERATION

 

Action 

Figure

Saw blade assembly and 
removing

See Fig. A

Safety on/off switch

See Fig. B 

Cross and rip cutting

See Fig. C1, C2

Using the laser light feature

See Fig. D1,D2

Replacing laser batteries

See Fig. E1-E3

Parallel guide

See Fig. F1, F2

Cutting depth adjusting

See Fig. G1,G2 

Cutting angle adjusting

See Fig. H

Pocket cutting

See Fig. I1,I2

Sawdust removal

See Fig. J

wORKINg HINTS FOR yOuR 

TOOL

If your power tool becomes too hot, please run 
your circular saw no load for 2-3 minutes to cool 
the motor. Avoid prolonged usage at very low 
speeds.
Protect saw blades against impact and shock. 
Cutting with extreme force can significantly 
reduces the performance capability of the tool 
and reduces the service life of the saw blade. 
Sawing performance and cutting quality depend 
essentially on the condition and the tooth count 
of the saw blade. Therefore, use only sharp saw 
blades that are suited for the material being cut.
Choice of blades: 24 teeth for general work, 
approx. 40 teeth for finer cuts, more than 40 
teeth for very fine cuts into delicate surfaces, 
diamond for tile, cement board, etc.
Only use saw blades recommended.

MAINTAIN TOOLS wITH 

CARE 

remove the plug from the socket before 
carrying out any adjustment, servicing or 
maintenance.

Keep tools sharp and clean for better and safer 
performance. Follow instructions for lubricating 
and changing accessories. Inspect tool cords 
periodically and if damaged, have repaired 
by authorized service facility. Your power tool 
requires no additional lubrication or maintenance. 
There are no user serviceable parts in your power 
tool. Never use water or chemical cleaners to 
clean your power tool. Wipe clean with a dry 
cloth. Always store your power tool in a dry place. 
Keep the motor ventilation slots clean. Keep all 
working controls free of dust. 
If the supply cord is damaged, it must be 
replaced by the manufacturer, its service agent 
or similarly qualified persons in order to avoid a 
hazard.
Periodically clear dust and chips from guard and 
base to ensure proper performance.

ENVIRONMENTAL 

pROTECTION

This product has been marked with a 
symbol relating to removing electric and 
electronic waste. This means that this 

product shall not be discarded with household 
waste but that it shall be returned to a collection 
system which conforms to the European 
Directive 2002/96/CE. It will then be recycled or 
dismantled in order to reduce the impact on the 
environment. Electric and electronic equipment 
can be hazardous for the environment and for 
human health since they contain hazardous 
substances.

Summary of Contents for WU427.1





















Reviews: