Worx WG776E Safety And Operating Manual Download Page 13

Page: 13 / 16

Cordless lawn mower

WG776E WG776E.9

NoTe:

To ensure long and reliable service, perform

the following maintenance procedures regularly.

Check for obvious defects such as a loose, dislodged

or a damaged blade, loose fittings, and worn or

damaged components. Check that the covers and

guards are all undamaged and are correctly attached

to mower. Carry out any necessary maintenance or

repairs before operating mower. If the mower should

happen to fail despite regular maintenance, please

call our customer helpline for advice.

blAde ShARPeNING

keeP BLaDe sHarP FOr BesT mOWer

PerFOrmanCe.

Wear PrOPer eYe PrOTeCTIOn WHILe remOVInG,

sHarPenInG, anD InsTaLLInG BLaDe. ensure

THaT saFeTY keY Is remOVeD.

sharpening the blade twice during a mowing season

is usually sufficient under normal circumstances.

sand causes the blade to dull quickly. If your lawn

has sandy soil, more frequent sharpening may be

required.

rePLaCe BenT Or DamaGeD BLaDe ImmeDIaTeLY.

WheN ShARPeNING The blAde:

1. make sure blade remains balanced.

2. sharpen blade at the original cutting angle.

3. sharpen cutting edges on both ends of blade,

removing equal amounts of material from both

ends.

To ShARPeN blAde IN A vISe (See fig. k)

1. Be sure the switch lever is released, the blade

has stopped and the safety key removed before

removing the blade.

2. remove blade from mower. see instructions for

removing and attaching blade.

3. secure blade k-1 in a vise k-2.

4. Wear safety glasses and be careful not to cut

yourself.

5. Carefully file the cutting edges of the blade with a

fine tooth file k-3 or sharpening stone.

6. Check balance of blade. see instructions for blade

balancing.

7. replace blade on mower and tighten securely.

refer to instructions below.

blAde bAlANcING (See fig. l)

Check balance of blade by placing center hole in blade

L-1 over a nail or screwdriver shank L -2, clamped

horizontally in a vise L-3. If either

end of the blade rotates downward, file that end.

Blade is properly balanced when neither end drops.

K-1

K-2

K-3

L-1

L-2

L-3

Summary of Contents for WG776E
















Search results

Summary of Contents for WG776E

Reviews:

Brands by name

Popular brands

Worx WG776E, Safety And Operating Manual

Search results

Summary of Contents for WG776E

Reviews:

Brands by name

Popular brands