Grass Trimmer ENG
11
10
11
10
TO REMOVE THE CAP
Press and hold in the two latches (12) (See J).
Pull cap away from the spool holder.
WHEN REFITTING THE SPOOL CAP
Keep all areas of the cap and spool holder
clean.
Replace the cap, pressing firmly down towards
the spool holder to ensure cap is fully located.
Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
TO REPLACE CUT LINE
For your convenience it is recommended you
buy spool and line complete.
TO FIT SPOOL AND LINE COMPLETE:
Remove old spool.
Place new spool into cap with
cut out areas of
the spool in line with eyelets.
Release one line from cleat and feed line
through eyelet.
Repeat for second line.
Refit the cap.
TO FIT NYLON LINE ONLY:
Warning!
Your Trimmer is designed to
use only line with a
maximum diameter
of 1.4mm.
IMPORTANT - Always wind the line onto
the upper section of the spool first.
Take approximately 5 metres of line. Insert
15mm of line into one of the holes in the
upper section of the spool and wind line in the
direction of the arrows on the top of the spool.
Leave approximately 100mm of line unwound
and place into cleat. Repeat on lower section
of spool.
Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
Then fit spool as described in
“To fit spool
and line complete”.
MAINTENANCE
After use, disconnect the machine from the mains
and check for damage. Your power tool requires
no additional lubrication or maintenance. There
are no user serviceable parts in your power
tool. Mains powered trimmers should only be
repaired by an authorised repairer use only
manufacturers recommended replacement
parts and accessories.
Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place
out of the reach of children. Keep the motor
ventilation slots clean. Keep all working controls
free of dust. If you see some sparks flashing in
the ventilation slots, this is normal and will not
damage your power tool.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your local authorities or retailer for recycling
advice.
PLUG REPLACEMENT (UK &
IRELAND ONLY)
If you need to replace the fitted plug then
follow the instructions below.
IMPORTANT
The wires in the mains lead are colored in
accordance with the following code:
BLUE =NEUTRAL
Brown = Live
As the colors of the wires in the mains lead of
this appliance may not correspond with the
colored markings identifying the terminals
in your plug, proceed as follows. The wire
which is colored blue must be connected to
the terminal which is marked with N. The wire
which is colored brown must be connected to
the terminal which is marked with L.
Warning:
Never connect live or neutral wires
to the earth terminal of the plug. Only fit an
approved 13ABS1363/A plug and the correct
rated fuse.
Note
: If a moulded plug is fitted and has to be
removed take great care in disposing of the
plug and severed cable, it must be destroyed
to prevent engaging into a socket.
CRA-WG101E WG104E -M-070104.indd 10
2007-3-28 17:08:42
Summary of Contents for WG101E
