Worx WA4096 Quick Start Manual Download Page 7

EN

7

GUTTERPRO Universal 
Gutter Cleaning Kit

SAFETY INSTRUCTIONS

WARNING!

 User must read the product manual to 

fully understand this product prior to use, and follow 

all safety instructions as outlined in the Worx AIR

TM

 

Operator’s Manual.

CAUTION!

The user must wear the appropriate 

clothing and safety goggles when operating this 

product. Be aware of all bystanders, pets and objects in a 

close proximity.

•  

DO NOT

 operate blower and attachments when 

fatigued.

•  

DO NOT

 overreach or stand on unstable support. Keep 

good footing and balance at all times.

•   Never direct airflow towards bystanders. Always be 

aware of the direction that the debris will be thrown.

•   Use a face filter mask to avoid breathing dust and 

debris.

WARNING: This product can expose you to 

chemicals including lead and Di(2-ethylhexyl)

phthalate (DEHP) which are known to the State of 

California to cause cancer and birth defects or other 

reproductive harm. For more information go to www.

P65Warnings.ca.gov.

COMPONENT LIST 

1.

GUTTER TUBE NOZZLE (QUANTITY OF 1) 

2. GUTTER TUBE EXTENSION (QUANTITY OF 3)

3. GUTTER TUBE ADAPTOR (QUANTITY OF 1) 

4. GUTTER TUBE CONNECTOR (QUANTITY OF 1)

5. UNIVERSAL ADAPTOR

6. BLOWER TUBE ADAPTOR

ASSEMBLY AND OPERATION

1. Attach the Gutter kit as shown in Fig. A1  (for 

Worx 

TURBINE, TRIVAC models and other brands blowers

), 

A2 (for 

WG545 models

), A3 (for 

WG543 models

):

Connect the (1, 2, 3) components by screwing together. 

Snap the (3, 4, 5) or (3, 4, 6) components together, and 

then tighten the screw (Fig. A4).

2. Assembling the Gutter Tube Adaptor

Fit the gutter tube adaptor to the motor housing as shown 

in Fig. B1.  Then tighten the screw. (Fig. B1.1) Check the 

gutter tube adaptor is firmly secured.

3. Assembling the Universal Adaptor

(1) Place the fabric side of the Universal Adaptor over the 

      Blower Outlet and slide it on as far as possible (B2).

      

Worx TURBINE

TM

 models

-Place the fabric side of the 

      Universal Adaptor over the outlet of the Fan Housing 

      and slide it on as far as possible(B2.1).

      

Worx TRIVAC

TM

 models

 - Place the fabric side of the 

      Universal Adaptor over the Vacuum Outlet and slide it 

      on as far as possible (B2.2). Before operation, flip the 

blow/vac switch into the vacuum mode.

 

PLEASE NOTE:

 Items can be vacuumed through the 

vac inlet and pass through or become clogged within 

the gutter kit. Please keep the vac inlet away from 

objects while using the gutter kit.

(2)  Check to make sure the strap is threaded through the 

locking mechanism. Then pull to tighten the strap 

(B3). Increase the tension by pulling the latch up and 

down to tighten (B4).  To loosen, simply press the two 

outside latches down and then pull the strap out from 

other side (B5).

(3)  Test that the Universal Adaptor will not slide off of the 

blower outlet.

(4)  If further tightening is needed, then pull the middle 

latch up and down until the adaptor is tight. Please 

recheck if it will slide off of the blower outlet. Realign 

and repeat these steps if needed (B4).  To loosen, 

simply press the two outside latches down and then 

pull the strap out from other side (B5).

PLEASE NOTE:

 The Universal Adaptor may have space 

between the Blower Outlet and Adaptor Outlet after 

installation. 

To remove the adaptor, simply press the two outside 

latches down and loosen the strap to remove it from the 

Blower Outlet (B5).

NOTE:

Use only enough Gutter Tube Extensions to comfortably 

reach the inside of the gutter.

4. Assembling the Blower Tube Adaptor (for 

WG543 

models

)

(1) Press the Nozzle Release Button to remove the 

Airspeed Selector Nozzle from the Blower Tube. (See Fig. 

C1)

(2) Slide the Blower Tube adaptor on and make sure it 

firmly locks into position. (See Fig. C2, C3)

(3) Attach the Gutter kit.

5. Operate according to Fig. D: 

The Gutter Tube Nozzle can be adjusted to any desired 

direction by rotating the Gutter Tube Connector as 

shown in Fig. E.  Gutter cleaning applications will vary. It 

is recommended to try various positions to find the most 

effective working position for the type of house and gutter 

design.

Reviews: