background image

Contents 

1-2-2 

071713 

PN=2 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

machine modifications that change the intended use, 

Modifications of this machine, or addition of unapproved 

weight or balance of the machine, or that alter machine 

products or attachments, may affect machine stability or 

controls, performance or reliability. 

AM40430,00000A9 -19-20AUG09-1/1 

Always contact an authorized dealer before making 

Non-John Deere parts, or any damage or failures resulting 
from their use are not covered by any John Deere warranty. 

Avoid Unauthorized Machine Modifications 

 

John Deere recommends using only genuine John Deere 

reliability, and may create a hazard for the operator or 

replacement parts to ensure  machine performance. 

others near the machine. The installer of any modification 

Never substitute genuine John Deere parts with alternate 

which may affect the electronic controls of this machine is 

parts not intended for the application as  these can 

responsible for establishing that the modification does not 

create hazardous situations or hazardous performance. 

adversely affect the machine or its performance. 

Wear Protective Equipment 

Guard against injury from flying pieces or metal or debris; 
wear goggles or safety glasses. 

Wear close fitting clothing and safety equipment 
appropriate to the job. 

Operating equipment safely requires the full attention of 
the operator. Do not wear radio or music headphones 
while operating machine. 

Prolonged exposure to loud noise can cause impairment 
or loss of hearing. Wear suitable hearing protection such 
as earmuffs or earplugs to protect against objectionable or 
uncomfortable loud noises. Radio or music headphones 
are not suitable to use for hearing protection. 

TX,WEAR,PE -19-22SEP10-1/1 

Inspect Machine 

Inspect machine carefully each day by walking around it 
before starting. 

Keep all guards and shields in good condition and properly 
installed. Fix damage and replace worn or broken parts 
immediately. Pay special attention to hydraulic hoses and 
electrical wiring. 

 
 
 
 

 

TX,INSPECT -19-08SEP10-1/1 

Stay Clear of Moving Parts 

Entanglements in moving parts can cause serious injury. 

Stop engine before examining, adjusting or maintaining 
any part of machine with moving parts. 

Keep guards and shields in place. Replace any guard 
or shield that has been removed for access as soon as 
service or repair is complete. 

 

TX03679,00016D2 -19-03JAN07-1/1 

T

1

3

3

5

9

2

 —

UN

1

5

A

P

R1

3

 

T

6

6

0

7

A

Q

 —

UN

1

5

A

P

R1

3

 

T

S

2

0

6

 —

UN

1

5

A

P

R1

3

 

Summary of Contents for 326D





















Reviews: