Safety and Comfort Accessories
Part #
Description
Part #
Description
3979
Ding Dong Chime Bell
303
Squeeze Bulb Horn
3973
Mega-Horn (battery operated)
201
Cable and Lock set (w/ keyed padlock)
4963
Rear View Mirror (Chrome, rectangular)
5032
Reflector Kit (Does not include 5031)
3978
Safety Flag on Pole
P19
Bicycle Helmet
101710
Flashing Strobe Light (clear lens)
101714
Flashing Strobe Light (red lens)
1006
Air Foot Pump
1000
Spoke Wrench
202
Mini-Frame Pump w/ Attachment Strap
2000
Chain Rivet Remover Tool
1265TW
Crank Cone Wrench
95021
Water Bottle w/ Cage & Strap
1001
Pedal Wrench
7917A
Backrest w/ Mounting Hardware
6001A
Patch Kit (5)
3976
Battery Operated Headlight
5848
Bar End Mirror
5030T
Reflector Set
SEATBELT
Seat Belt
– Lap Type
95021
Water Bottle and Holder
TRAILER
Heavy Hauler Trailer
THA-PAVSBST Trailer Hitch Kit (needed for trailer)
FOOTREST
Foot Rest (Good for fixed-drive models.)
PSCUP
Cup Holder Deluxe - Armrest Mounted
7217-41197
Pedals: Velcro Foot Strap (1 Strap)
7217-41038
Pedals: Weighted Platform (1 Strap)
7217GS12
Pedals:
“Glowspeck” Flashing
7217-300622
Pedals: Large Platform w/ Full Straps
ENG-BKIT-20WTC
Electric Drive System* (Inquire for details before ordering!)
* Electric Drive Systems are subject to state and local approvals. The Purchaser assumes responsibility for meeting legal ordinances. Subject to availability.
Worksman Stretched Mover
Worksman Personal Activity Vehicle
Eagle Lite Trike
Exploded view of L500-F
1265 Crank Parts Set with 1275 Crank
M13975 Axle Bearing w/Plate
A
SSEMBLY
I
NSTRUCTIONS FOR
T
HE
W
ORKSMAN
S
IDE BY
S
IDE
T
EAM
D
UAL
T
RICYCLE
:
Please read this manual carefully prior to performing the simple finishing adjustments and prior to riding. Keep these instructions, as
our parts list is contained within this document which you will need for future reference. Carefully remove the tricycle from the carton.
You will notice the tricycle is pre-assembled at the factory. Some finishing assembly / adjustments are required.
I
NSTALLING AND
A
DJUSTING
T
HE
H
IGH
B
ACK
C
APTAIN
’
S
S
EAT
:
Your SBST Tricycle comes with thickly padded captain
’s seats.
1. Position the seat on the sliding seat track.
2. With the T-Bolt upside down, insert seat hardware onto the T-Bolt as follows: 1) Spacer Tube > 2)
Washer > 3) Rectangular Bracket > 4) Winged Bracket with the wings facing up.
3. Thread the
“T” bolt (still upside down) into the bottom of the seat. Slide the seat to a comfortable
position where leg is slightly bent at the knee when the pedal is at its furthest position away from you.
Tighten the bolt so seat is secure and no longer slides across the track. Remember to always check
tightness of seat before riding.
A
DJUST
H
ANDLEBAR
:
The Side by Side comes with a steering tiller. It can be positioned for your own riding preference. The stem is not tightened at the
factory for height or alignment, so you can set it where you desire by simply lifting the tiller to a comfortable position and tightening the
four stem bolts using a 5mm hex key. The stem must be inserted to the minimum insertion line marked on the stem. Make certain
the stem is tight and the tiller remains up even while exerting downward pressure. Once straight, tighten the central alignment bolt on
the stem using a 6mm hex or adjustable wrench depending on style of stem so that handlebar and front wheel are aligned.
(Please
note that stem specifications are subject to change without written notice. Verify the sizes of the hexes before tightening.)
I
NSTALL
B
ASKET
:
1) Remove the basket straps from the rear frame assembly/basket mount.
2) Place basket on top of frame assembly.
3) Place basket straps inside basket and install hardware as it was assembled prior to removing straps.
I
NSTALL
R
EFLECTORS
:
- One rear reflector (red) goes on the back of each seat. Peel the backing off, stick to the center of back of seat.
- The front reflector (white square) installs through the front reflector bracket on the headset assembly.
- The wheel reflectors (white arched or rectangular) install on the inside of the two layers of spokes. The spoke
has a groove that will be facing you that is placed onto the spoke. Insert a bolt though the hole, sandwiching the spoke between the
reflector and the head of the bolt as shown. The bolt will thread into a nut that must be placed into the back of the reflector.
