background image

1

34

TABLE OF CONTENTS

WARRANTY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INFORMATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SAFETY SIGNS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . 13

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 18

SERVICE INSTRUCTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

SPECIFICATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

TROUBLE-SHOOTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PARTS LISTS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-34

TO THE OWNER:

Read this manual before using your Hydraulic Post Driver. This manual is provided to give you the necessary

operating and maintenance instructions for keeping your Hydraulic Post Driver in top operating condition. Please
read this manual thoroughly. Understand what each control is for and how to use it. Observe all safety signs on
the machine and noted throughout the manual for safe operation of implement. Keep this manual handy for ready
reference.

Like all mechanical products, it will require cleaning and upkeep. Lubricate the Post Driver as specified.

Use only genuine Worksaver, Inc. service parts. Substitute parts will void the warranty and may not meet stan-

dards required for safe and satisfactory operation. Record the model and serial number of your Post Driver here:

Model:________________________________________  Serial Number:_______________________________

RETAIL CUSTOMER’S RESPONSIBILITY

It is the Retail Customer and/or Operator’s responsibility to read the Operator’s Manual, to operate, lubri-

cate, maintain, and store the product in accordance with all instructions and safety procedures. Failure
of the operator to read the Operator’s Manual is a misuse of this equipment.

It is the Retail Customer and/or Operator’s responsibility to inspect the product and to have any part(s)

repaired or replaced when continued operation would cause damage or excessive wear to other parts or
cause a safety hazard.

It is the Retail Customer’s responsibility to deliver the product to the authorized Worksaver Dealer, from

whom he purchased it, for service or replacement of defective parts which are covered by warranty.
Repairs to be submitted for warranty consideration must be made within forty-five (45) days of failure.

It is the Retail Customer’s responsibility for any cost incurred by the Dealer for traveling to or hauling

of the product for the purpose of performing a warranty obligation or inspection.

SINO LEEINGLES, PIDA AYUDA A
AIGUIEN QUE SI LO LEA PARA QUE
LE TRADUZCA LAS MEDIDAS DE
SEGURIDAD.

STATEMENT

OF POLICY

It is the policy of Worksaver,

Inc. to improve its products where
it is possible and practical to do
so. Worksaver, Inc. reserves the
right to make changes or
improvements in design and con-
struction at any time, without
incurring the obligation to make
these changes on previously
manufactured units.

HYDRAULIC FRONT LOADER MOUNT PARTS LIST

Summary of Contents for HPD-16 HFL





































Reviews: