manualshive.com logo in svg

Worcester GR2300iW C, Installation And Maintenance Instructions Manual

Share
Download
Worcester GR2300iW C Installation And Maintenance Instructions Manual Download Page 17

Pre-Installation

17

Greenstar 2000 – 6 721 820 552 (2021/02)

NOTICE

Damage to system:

The heating system pipe work can be damaged by frost if installed in an 
internal unheated area, such as a loft, basement or garage.
The appliance internal frost protection only monitors the system water 
temperature within the appliance to provide protection for the 
appliance.

▶ System frost protection can be achieved when using either Worcester 

weather-compensating controls or via a hard-wired thermostat when 
using external 230v controls (refer to figure 58, page 43).

▶ The system pipe work in the internal unheated area should be 

insulated.

▶ If the appliance is to be shut down for an extended period, drain the 

central heating system.

The appliance must be installed where:

▶ The area is well lit, allowing users to clearly see the appliance to carry 

out any work or checks.

▶ An engineer can gain clear and safe access to work on the product or 

component, including making adequate provision for visual 
inspection of flues in voids.

▶ The homeowner can gain clear and safe access to the controls or to 

check, top up or reset the appliance.

▶ Roof space installations must fully conform to BS 5410 part 1: roof 

space installations.

▶ Products in roof spaces must have permanent fixed lighting, a 

permanent fixed retractable ladder and a fixed floor area sufficient to 
allow access for normal use and servicing around the product and 
between the product and the access hatch.
We would also recommend that a remote pressure gauge and filling 
loop are sited where the customer can gain easy access to assist with 
checking and topping up.

4.3.2

Rooms containing a bath or shower

CAUTION

Risk of electric shock

▶ Any switch or appliance control using mains electricity must not be 

within reach of a person using the bath or shower.

• In all cases the installation 

must be in accordance with the latest 

amendments to the latest edition of the IET Wiring Regulations 
(BS7671)

.

• Check the IP rating of any control units to be used on this appliance. 
• Circuit breaking devices should be used in accordance with the 

regulations.

• Figure 10 is for guidance only.

Fig. 10 Bathroom installations

[0]

Zone 0

[1]

Zone 1

[2]

Zone 2

[2*]

Without the end wall, zone 2 must extend 600mm from the bath

[A]

600mm radius from the bath or shower

• Appliance protection rating - IPX4D

0010017086-002

2

1

2

1

2

2

1

600mm

600mm

600mm

2250mm

2250mm

2*

A

A

A

600m

m

Summary of Contents for GR2300iW C





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands