Worcester DT10RF Instruction Manual Download

Page: 8 / 24

MMI

NIN

TRANSMITTER LOCATION

CLEARANCES & FIXING

FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH

DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER

8-716-106-652 issue c (01.05) UK

TRANSMITTER LOCATION
CLEARANCES & FIXING

CAUTION:

Ensure there are no

pipes, electric cables or other

hazards before drilling.

SAFETY:

All relevant safety

precautions must be undertaken.

Protective clothing, footwear, gloves

and safety goggles must be worn

as appropriate.

Transmitter location:

Position the transmitter (A) as close

to the main living area as possible

onto a flat inside wall, approx. 1.5m

(5') above the floor within max. signal

range of the appliance receiver.

Keep the transmitter away from:

light and heat sources
enclosures and curtains
direct draughts, including fans, air

vents, windows and doors
damp and condensation

Replacing a mains wired unit:

Isolate the main electric supply. Refer

to the manufacturers instructions to

remove the unit. Isolate the existing

wiring and make electrically safe.

Transmitter clearances:

See diagram opposite for minimum area

required for operation.

Transmitter fixing:

Loosen screw (C) on transmitter to

remove the baseplate (B)

Hold baseplate (B) level to mark

securing points (D) and remove

baseplate (B)

Drill holes to marks
Fit one wall plug into each hole
Reposition baseplate (B), check

level and secure with screws supplied

Refit the transmitter to the baseplate

(B) and tighten screw (C) to secure.

1 2 3

1.5m (5)

SET?

SELECT

YES

Digistat Optimiser

50mm

70mm

All manuals and user guides at all-guides.com

Summary of Contents for DT10RF

























Search results

Summary of Contents for DT10RF

Reviews:

Related manuals for DT10RF

Brands by name

Popular brands

Worcester DT10RF, Instruction Manual

Search results

Summary of Contents for DT10RF

Reviews:

Related manuals for DT10RF

Brands by name

Popular brands