background image

14

 Assembly

MAN0761 (11/14/2008)

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

Assembly  of  this  Box  Scraper  is  the  responsibility  of
the WOODS dealer. It should be delivered to the owner
completely assembled and adjusted for normal condi-
tions.

Complete the Check Lists on page 15 before delivering
the attachment to the customer.

The  Box  Scraper  is  shipped  partially  assembled.
Assembly will be easier if components are aligned and
loosely  assembled  before  tightening  hardware.  Rec-
ommended torque values for hardware are located on
page 18.

Before performing any service or maintenance,

lower attachment to ground, turn off engine, set
parking brake, and remove key.

NEVER  GO  UNDERNEATH  EQUIPMENT.  Never

place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.

• Service  work  does  not  require  going  under-
neath implement.
• Read  Operator's  Manual  for  service  instruc-
tions or have service performed by a qualified
dealer.

Keep  all  persons  away  from  operator  control

area while performing adjustments, service, or
maintenance.

Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate

.

BOX SCRAPER

Assemble Box Scraper

1.

Remove  the  banding,  straps  and  lag  bolts  that
holds  the  box  scrapers  and  mast  plates  to  the
pallet.

 Figure 8

. Shipping Configuration - Box Scraper

2.

Place right mast plate (2) to the inside of right cross
support  bar  and  secure  into  position  using  three
hex  flange  screws  (19)  and  flange  lock  nuts  (17).
See page 16 for part diagram.

3.

Repeat step to install left mast plate (3).

4.

Place  spacer  sleeve  (23)  between  mast  plates
lower front hole and secure into position using cap
screws  (22)  two  (one  on  either  side)  flat  washers
(21) and lock nuts (20). Install second sleeve (23)
in lower rear hole.

5.

Tighten  5/8  hardware  to  170  lbs-ft  and  3/4
hardware to 297 lbs-ft.

 Figure 9

. Spacer Sleeve Installation

INSTALL TAILGATE ON BSM MODELS 

(OPTIONAL)

1.

Remove rear cutting edge from box scraper.

2.

Place tailgate (5)  against  rear  of  box  scraper  and
align mounting holes.

3.

Insert  tailgate  pins  (4)  through  holes  on  box
scraper  and  tailgate.  Secure  tailgate  pin  into
position  using  flat  washers  (24)  and  spring  pins
(15).

4.

Attach cutting edge against tailgate and align holes
and secure into position using hardware previously
removed. 

WARNING

CAUTION

23

21

20

3

2

(Rev. 1/23/2009)

Summary of Contents for BSM72























Reviews: