background image

Owner Service 

17

MAN0050 (Rev. 1/16/2004)

TROUBLE SHOOTING

MOWING CONDITIONS

PROBLEM

POSSIBLE CAUSE

SOLUTION

Grass cut lower in center of swath 
than at edge

Height of cutter lower at rear or 
front

Adjust cutter height and attitude so 
that cutter rear and front are within 
1/2" of same height. 

Streaking conditions in swath

Conditions too wet for mowing

Allow grass to dry before mowing.

Blades unable to cut that part of 
grass pressed by path of tractor 
tires

Slow ground speed of tractor but 
keep engine running at full PTO 
RPM. Cutting lower will help.

Dull blades

Sharpen or replace blades.

Material discharges from cutter 
unevenly; bunches of material 
along swath

Material too high and too much 
material

Reduce ground speed but main-
tain 540 RPM at tractor PTO or 
make two passes over material.
Raise cutter for the first pass and 
lower to desired height for the sec-
ond and cut at 90° to first pass. 
Raise rear of cutter high enough to 
permit material to discharge but 
not so high as to cause conditions 
listed above.

Grass wet

Allow grass to dry before mowing. 
Slow ground speed of tractor but 
keep engine running at full PTO 
RPM. Cutting lower will help.

Rear of cutter too low, trapping 
material under cutter

Adjust cutter height and attitude.

Cutter will not cut
(Shear bolt drive only)

Shear bolt sheared

Install new shear bolt.

Cutter will not cut all the time
(Slip clutch drive only)

Slip clutch slipping

Adjust slip clutch according to 
instructions in Adjust Slip Clutch, 
page 14.

Summary of Contents for BRUSHBULL BB48



























































Reviews: