44
Dealer Check Lists
MAN0725 (10/3/2008)
DEALER CHECK LISTS
PRE-DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
Inspect the equipment thoroughly after assembly to
ensure it is set up properly before delivering it to the
customer.
The following check lists are a reminder of points to
inspect. Check off each item as it is found satisfactory
or after proper adjustment is made.
NOTICE
■
Gearboxes are not filled at the factory. Prior to
delivery, make sure each gearbox is filled between
lowest ring and end of dipstick with 80 or 90W API
GL-4 or GL-5 gear lube.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check that shields and guards are properly
installed and in good condition. Replace if dam-
aged.
___ Check all bolts to be sure they are properly
torqued.
___ Check wheel bolts for proper torque.
___ Check that all cotter pins and safety pins are
properly installed. Replace if damaged.
___ Check that blades have been properly installed.
___ Check and grease all lubrication points as identi-
fied in lubrication information on page 20.
___ Check the level of gearbox fluids before delivery.
Service, if required, as specified in the lubrication
information on page 20.
DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
___ Show customer how to make adjustments and
select proper PTO speed.
___ Show customer how to make sure driveline is
properly installed and that spring-activated lock-
ing pin or collar slides freely and is seated in
groove on tractor PTO shaft.
___ Show customer how to determine the turning lim-
its of the CV PTO driveline.
___ Show customer the safe, proper procedures to be
used when mounting, dismounting, and storing
equipment.
___ Make customer aware of optional equipment
available so that customer can make proper
choices as required.
___ Instruct customer how to lubricate and explain
importance of lubrication.
___ Point out the safety decals. Explain their meaning
and the need to keep them in place and in good
condition. Emphasize the increased safety haz-
ards when instructions are not followed.
___ Explain to customer that when transporting the
cutter, the wing and center sections should be
raised and their respective transport bars
installed and pinned in place.
___ Present Operator's Manual and request that cus-
tomer and all operators read it before operating
equipment. Point out the manual safety rules,
explain their meanings and emphasize the
increased safety hazards that exist when safety
rules are not followed.
___ Explain to customer the potential crushing haz-
ards of going underneath raised equipment.
Instruct that before going underneath to discon-
nect the driveline, securely block up all corners
with jack stands and to follow all instructions in
the BLOCKING METHOD, page 19 of the opera-
tor’s manual. Explain that blocking up prevents
equipment dropping from hydraulic leak down,
hydraulic system failures or mechanical compo-
nent failures.
___ Point out all guards and shields. Explain their
importance and the safety hazards that exist
when not kept in place and in good condition.
___ Explain to customer that when towing on a public
road to comply with all state and local light-
ing/marking laws and to use a safety tow chain.
Summary of Contents for Batwing BW240Q
