Woods ALITEC PS9 1.5HD SINGLE CIRCUIT Operator'S Manual Download Page 15

Page: 15 / 40

Troubleshooting

MPS9 (Rev. 4/20/2007)

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Cutting wheel rotates in the wrong

direction.

Auxiliary hydraulics are being

activated in the wrong direction.

Reverse direction of auxiliary flow.

Quick disconnects are switched on

auxiliary hoses.

Switch male and female auxiliary

QDs.

Hydraulic sideshift is not operating.

Diverter valve is set to the cutting

position.

Make sure the diverter valve knob is

pulled outward as far as possible.

Hoses to the sideshift cylinder are

obstructed.

Remove and visually inspect hoses.

One or more seals in the sideshift

cylinder have failed.

Contact dealer.

Obstruction between pivot frame and

side frame.

Remove obstruction.

Insufficient hydraulic flow from skid

steer.

Refer to skid steer owner’s manual.

Air is trapped in the sideshift cylinder

hoses.

Remove hoses from cylinder,

activate sideshift function to

evacuate air and re-attach hoses.

Cylinder rod is bent.

Visually inspect cylinder for damage.

Oil leaking from sideshift cylinder.

One or more seals on cylinder have

failed.

Contact dealer.

O-rings on fittings are damaged.

Visually inspect O-rings and replace

as needed.

Fittings are loose or damaged.

Tighten or replace as needed.

Hydraulic hoses are loose or

damaged.

Tighten or replace as needed.

Excessive vibration during cutting

operation.

Picks are excessively worn.

Visually inspect picks and replace as

needed.

Insufficient down force due to

incorrect operating procedure.

Refer to the “Operation” section.

Pivot pins excessively worn.

Remove pins and inspect for wear.

Summary of Contents for ALITEC PS9 1.5HD SINGLE CIRCUIT









































Search results

Summary of Contents for ALITEC PS9 1.5HD SINGLE CIRCUIT

Reviews:

Related manuals for ALITEC PS9 1.5HD SINGLE CIRCUIT

Brands by name

Popular brands

Woods ALITEC PS9 1.5HD SINGLE CIRCUIT, Operator'S Manual

Search results

Summary of Contents for ALITEC PS9 1.5HD SINGLE CIRCUIT

Reviews:

Related manuals for ALITEC PS9 1.5HD SINGLE CIRCUIT

Brands by name

Popular brands