background image

Rev 8.0/6-13 

22 

MRTALPCH6-DC: #35054 

CAUTION:    Be sure to use appropriate cleaning methods for each type of electrical 

component, as specified by codes and standards.    Improper cleaning 

can damage components. 

• Keep a written record of all Periodic Inspections. 
If any deficiency is detected during the inspection, correct it before using the lifter.    If 

necessary, return the lifter to Wood’s Powr-Grip or an authorized dealer for repair (see LIMITED 
WARRANTY). 

Infrequent Use 

If a lifter is used less than 1 day in a 2-week period, perform the Periodic Inspection 

each time 

before using the lifter. 

T

ESTING 

S

CHEDULE

 

Perform these tests when placing the lifter in service 

initially and each time following a repair or 

modification.    Correct any deficiency and retest before using the lifter. 

Operational Tests 

• Perform the V

ACUUM 

T

EST

 to follow. 

• Test all features and functions of the lifter (see OPERATING FEATURES, OPERATION and 

MAINTENANCE). 

Load Test 

Prove that the lifter can lift 100% of its Maximum Load Capacity (see SPECIFICATIONS), using an 

actual load or an equivalent simulation.

13

    Employ the following method to test with an actual 

load: 
1)  Place a test load with appropriate L

OAD 

C

HARACTERISTICS

 (see INTENDED USE) on a stable 

support.    Make sure the load is oriented in the upright position.

14

 

2)  Apply the vacuum pads to the load as previously directed. 
3)  After the vacuum pump stops running, place the lifter's power switch in the "OFF" position. 
4)  Raise the load a minimal distance, to assure that it is supported by the lifter. 
5)  Hold the load for 5 minutes.    The load must not slip or fall during this time period.    If it 

does, conduct a V

ACUUM 

T

EST

 and inspect each vacuum pad as indicated under V

ACUUM 

P

AD 

M

AINTENANCE

: Inspection (see sections to follow).    Correct any deficiency that is found and 

retest the lifter. 

 
Note:    See MAINTENANCE topics to follow for additional directions about inspecting and testing 
specific lifter components.    Since the low vacuum warning buzzer is controlled by a vacuum 

switch, consult the V

ACUUM 

S

WITCH 

A

DJUSTMENT

 discussion for inspection, testing and adjustment 

procedures. 

                                        

13

    ASME Standard B30.20 requires the lifter to be tested to 125% of its Load Capacity. 

14

    Flat Lifters are exempt from this requirement. 

Summary of Contents for Powr-Grip MRTALPCH610DCO







































Reviews: