Screws 35mm
Install a drawers board between notches
Diagram1.3
Diagram 1.4
Start with the assembly of horizontal beams
W1, W8, W14 and W19
(W = horizontal, S = vertical). The
labels as shown on , can be found on the end of each beam. Position the beams on the floor so
that you can walk around the bed while it is in the building phase ( ).
WARNING! All horizontal beams (W1, W2, W3, W7, W8, W9, W10, W11, W12) should be set up so
that the side with the most circular indentations (= ), face the inner side, while the side with
only two indentations face underneath. The surface of beams W13, W15, W16, W17 and W23 with
round indentations should face the inner side.
During the beam assembly install the
falthead bolts
from
outside to inside
. From the inside finally
screw a size 6 flange nut using a screwdriver with size 10 attachment. But do not over tighten bolts.
Diagram1.1
Page 2
Set up the corner beams Z30 and Z31, S1 and S8 like the middle beams S2 and S7
. Make sure that the beam side with round
indentations on
Z30, Z31 and beam side with five round indentations on S1, S5, S6 and S8 face the middle beams.
Continue to follow the instructions + + . The beams W17 and W23 can be interchanged depending on whether you
want to attach the bed to the wall using the beam W23.
The beams W2, W3, W9 and W10
, has notch to support the mattress slats and
these notch should face upward. For the beams
W13 - W23
there will be an
additional bolts for the end of vertical beams, which are from fixed from top to
bottom at the end of the beam with M6 flange nut. The horizontal beams on the
upper bunk are built from top to bottom so that it makes it easier to screw nuts
with screwdriver. Then tightly screw the bolts at the bottom so that it makes it
easier to construct the rest of the bed.
Ladder assembly:
in one end of five rung holes of beam S3 add drops of wood
glue (included in delivery). Tap in the steps using a hammer and wooden board
( ). Do not put glue on the other side so that another step can be added
later to raise the height to 150 cm!
Diagram 1.3
Before installing slats for mattress support assemble the
drawers
together. Place drawer board in the notch
between the font and back board and attach the side
boards to front and back with screws ( ) . Fix small
wheels on a wooden block attached to the side boards
( ). Both drawers should be placed from the top
through the space between the beams W1 and W2 from
inside to outside . Corner boards
F1, F2 and F3
should be
attached to the beams Z30/Z31, S1/Z32 and S7/S8 with
40
x 40-mm-Brackets
. So that the drawers slide along the
corner boards. The corner boards with wider ends should
be positioned in the back ( ).
Diagram 1.4
Diagram 1.5
Diagram1.5
Leave it free for
further assembly
option.
3 drops of glue
on one end of rung
holes.
Attach the steps with a glue only on one side so
that you could add another step for a further
assembly option.
Place a wood plate
when using a hammer
to prevent dents.
S3
S4
Diagram 1.5
F2
F3
Fix wheels to the wooden
blocks from below using
the screw 16 mm.
Z31
W1
S8
Install the drawer on the right side between the corner
board F1 and beams S7 and S8.
W8
1.
1.
3.
2.
WARNING!
First attach the corner piece to the
corner board and than to the bed.
16mm 35mm
screws
110 mm
flathead bolt
flange nut
M6
WOODLAND reserves the right for printing errors © Copyrights by WOODLAND 1998
R
