In order to set the cutter length the following simple formula can be used:
cutter length = (x – 25mm)/2 where x = the size of hole needed.
So if you want to cut a 42mm hole the cutter should be set at 8.5mm
i.e. 42mm -25mm = 17mm 17/2 = 8.5mm
Using the Woodcut MillDrill to hold Forstner bits
The Woodcut MillDrill has the added feature of being able to act as a chuck for drill bits with
a 10mm shank. Many forstner bits, for example have reduced shanks that measure 10mm
and these can be inserted into the front of the Woodcut MillDrill. Before doing so the front
cutter needs to be removed and then, with the drill bit inserted in the front hole, the two
grub screws can be tightened.
The Woodcut MillDrill is now ready to be inserted in the tailstock and drilling can take place
on the lathe negating the need for a Jacobs chuck.
M
ILL
D
RILL
®
M
ILL
D
RILL
+
W
OOD
+
C
RUSH
G
RIND
=
G
RINDER
For easy installation of CrushGrind® mechanisms
www.woodcut-tools.com
www.woodcut-tools.com
WOODCUT TOOLS LIMITED
P.O.Box 57, Clive, Hawkes Bay, New Zealand
Phone: + 64 6 875 1066, Fax: + 64 6 875 1067
GENERAL SAFETY RULES
Warning! Failure to follow these rules may result in serious personal injury.
1 FOR YOUR OWN SAFETY, READ THE MANUAL BEFORE OPERATING THE TOOL. Learn the machine’s application
and limitations plus the specific hazards peculiar to it.
2 ALWAYS USE SAFETY GLASSES – FULL FACEMASK strongly recommended. Safety glasses (must comply with
ANSI STANDARD Z87.1 USA) Everyday eye glasses usually are only impact resistant; they are not safety
glasses. Also use face or dust mask if cutting operation is dusty.
3. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewellery,
which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering
to contain long hair.
4. USE EAR PROTECTORS. Use earmuffs for extended period of operation. Use muffs rated to 103 DBA LEQ (8
hr).
5. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them
to rain. Keep work area well lighted.
6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. Build up of sawdust is a fire hazard.
7. KEEP CHILDREN AND VISITORS AWAY. All children, infirm and visitors should be kept a safe distance from
work area.
8. AVOID ACCIDENTAL STARTING. Make sure switch is in the Off position before plugging in power cord.
9. NEVER LEAVE MACHINE RUNNING UNATTENDED. Do not leave tool unless it is turned off and has come to a
complete stop.
10. KEEP GUARDS IN PLACE and in working order.
11. USE RIGHT TOOL. Do not use a tool or attachment to do a job for which it was not designed.
12. DON’T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed.
13. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
14. DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol or any
medication.
15. DUST WARNING. The dust generated by certain woods and wood products can be harmful to your health.
Always operate machinery in well ventilated areas and provide for proper dust removal. Use wood dust
collection systems whenever possible.
16. ENSURE THAT YOUR WORK IS SECURELY HELD IN THE LATHE before switching the lathe on.
Developed in association with top Australian woodturner Brendon Stemp.
TM
