Woodbridge BID 02 Installation Manual Download Page 11

Page: 11 / 14

WOODBRIDGE

Neutral cleaner

When there is dirt on the nozzle, maintain it according to the following methods:

1. When no one is seated, turn the knob forward (press Rear Cleaning Button on the main unit), then nozzle rod

is extended, and manually clean with a rag or soft brush.

2. Nozzle can be removed and cleaned separately. (Hold the nozzle rod in one hand and pull the nozzle out with

the other hand)

3. Put back the nozzle, and then press the knob button (Stop button) on the main unit or the "Stop" button on the

remote control, the guided rod retracts.

Filter Maintenance

Tips: Do not pull the nozzle rod to prevent the damage of the nozzle rod and motor.

Maintenance of Main Unit

Daily Maintenance

1.Turn off the power during maintenance of this machine.

2. Wipe the dirty area with a soft cloth that is wrung out of water.

3. After wiping, please turn on the power again.

Tips: Do not rinse the surface of the product directly with water

during maintenance.

Maintenance of the Nozzle

Time for maintenance: It is under normal

water pressure but poor flush performance

occurs.

1. Turn off the angle valve.

2. Unscrew toilet water inlet pipe and seat

water inlet pipe.

3. Take out filter and filter washer

4. Brush filter with toothbrush and clean filter

5. Re-install filter and filter washer, then

re-install water inlet pipe

3-way

connector

The filter

(Remove with

a nipper pliers)

Filter

washer

Connect to toilet

water supply pipe

Connect to seat water

inlet pipe

www.woodbridgebath.com

Summary of Contents for BID 02















Search results

Summary of Contents for BID 02

Reviews:

Woodbridge BID 02, Installation Manual, Page: 11 / 14

Search results

Summary of Contents for BID 02

Reviews: