Wood Stone Fire Deck WS-FD-6045 Installation And Operation Manual Download Page 6

Page: 6 / 31

air intake: Do not

facade or cover over
must be left

removable for service

Unit Shipping Weight:

3,200 lbs.

UTiLiTies speciFicaTions

Gas:

3/4 inch Fnpt gas inlet

160,000 btu/hr natural gas (ng)
Or
160,000 btu/hr propane (lp)

Optional Decorative Flame adds

15,000 btu/hr to total rated input

Maximum gas inlet pressure:

1/2 psi (14 inches W�c�)

Venting

the Fire Deck 6045 must be vented using a listed type

1 exhaust hood, or a hood constructed and installed

in accordance with nFpa 96 and all relevant local and

national codes� the oven must be vented in accordance

with all relevant local and national codes, and in a

manner acceptable to the authority having jurisdiction�

Important:

models with -W in the model number must

be vented as a solid fuel appliance�

Electrical

120 vac, 1�1 a, 50/60 Hz

240 vac� 1 a, 60 Hz (optional)
electrical connection always on the

left side of the oven� gas connection

on same side as radiant burner (left

or right option)�
refer to data plate when installing�

NOTE

this oven is available in a left or

right side burner configuration�

gas connections will be on

the same side of the oven as

the radiant flame� electrical

connections are always on the left�
Shown: right side burner

configuration�

An ongoing program of product improvement may require us to change
specifications without notice.

FD-6045, Revised October 2013

[email protected]

or visit

woodstone-corp.com

wood stone corporation

1801 w. bakerview rd.
bellingham, wa 98226 usa

tf. 800.988.8103
t. 360.650.1111
f. 360.650.1166

FD-6045 SPECIFICATIONS

FD-6045 Fire Deck Oven

installation and Operation manual

Side view

REV:

LEGEND:

PART #:

FD-6045-Gas-R

6045 Fire Deck

General Arrangement

10/11/2013

bena

DWN BY:

SHEET:

Bellingham, WA 360/650-1111 www.woodstone-corp.com

DIMENSIONS ARE IN INCHES

TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°

UNLESS NOTED OTHERWISE

\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-6045_General_Arrangement-1.dft

THE INFORMATION CONTAINED IN THIS DRAWING IS THE

SOLE PROPERTY OF WOOD STONE CORPORATION

ANY REPRODUCTION OR USE IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS

PROHIBITED

AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT

MAY REQUIRE US TO CHANGE SPECIFICATIONS

WITHOUT NOTICE.

DATE:

120VAC, 4A

GAS INLET: 3/4" NPT
160,000 BTU, NG
160,000 BTU, LP

1 of 1

AIR INTAKE

60"

1520mm

100mm

24 3/4"

630mm

25 1/2"

650mm

37 1/2"

950mm

46 1/4"

1180mm

23 3/4"

600mm

3 3/4"

100mm

48"

1220mm

33 3/4"

860mm

10"

250mm

13 3/4"

350mm

10 1/4"

260mm

7 1/4"

180mm

9 3/4"

250mm

1 1/4"

30mm

100mm

48 1/4"

1230mm

29 3/4"

760mm

R 11 1/2"

290mm

Swing Radius

3 3/4"

100mm

74 1/2"

1890mm

34"

860mm

17 3/4"

450mm

13 1/4"

340mm

52 3/4"

1340mm

7 1/2"

190mm

3 1/2"

90mm

9 3/4"

250mm

23"

580mm

2 3/4"

70mm

43"

1090mm

150mm

78 1/4"

1990mm

Plan view

Front view

REV:

LEGEND:

PART #:

FD-6045-Gas-R

6045 Fire Deck

General Arrangement

10/11/2013

bena

DWN BY:

SHEET:

Bellingham, WA 360/650-1111 www.woodstone-corp.com

DIMENSIONS ARE IN INCHES

TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°

UNLESS NOTED OTHERWISE

\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-6045_General_Arrangement-1.dft

THE INFORMATION CONTAINED IN THIS DRAWING IS THE

SOLE PROPERTY OF WOOD STONE CORPORATION

ANY REPRODUCTION OR USE IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS

PROHIBITED

AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT

MAY REQUIRE US TO CHANGE SPECIFICATIONS

WITHOUT NOTICE.

DATE:

120VAC, 4A

GAS INLET: 3/4" NPT
160,000 BTU, NG
160,000 BTU, LP

1 of 1

AIR INTAKE

60"

1520mm

100mm

24 3/4"

630mm

25 1/2"

650mm

37 1/2"

950mm

46 1/4"

1180mm

23 3/4"

600mm

3 3/4"

100mm

48"

1220mm

33 3/4"

860mm

10"

250mm

13 3/4"

350mm

10 1/4"

260mm

7 1/4"

180mm

9 3/4"

250mm

1 1/4"

30mm

100mm

48 1/4"

1230mm

29 3/4"

760mm

R 11 1/2"

290mm

Swing Radius

3 3/4"

100mm

74 1/2"

1890mm

34"

860mm

17 3/4"

450mm

13 1/4"

340mm

52 3/4"

1340mm

7 1/2"

190mm

3 1/2"

90mm

9 3/4"

250mm

23"

580mm

2 3/4"

70mm

43"

1090mm

150mm

78 1/4"

1990mm

REV:

LEGEND:

PART #:

FD-6045-Gas-R

6045 Fire Deck

General Arrangement

10/11/2013

bena

DWN BY:

SHEET:

Bellingham, WA 360/650-1111 www.woodstone-corp.com

DIMENSIONS ARE IN INCHES

TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°

UNLESS NOTED OTHERWISE

\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-6045_General_Arrangement-1.dft

THE INFORMATION CONTAINED IN THIS DRAWING IS THE

SOLE PROPERTY OF WOOD STONE CORPORATION

ANY REPRODUCTION OR USE IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS

PROHIBITED

AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT

MAY REQUIRE US TO CHANGE SPECIFICATIONS

WITHOUT NOTICE.

DATE:

120VAC, 4A

GAS INLET: 3/4" NPT
160,000 BTU, NG
160,000 BTU, LP

1 of 1

AIR INTAKE

60"

1520mm

100mm

24 3/4"

630mm

25 1/2"

650mm

37 1/2"

950mm

46 1/4"

1180mm

23 3/4"

600mm

3 3/4"

100mm

48"

1220mm

33 3/4"

860mm

10"

250mm

13 3/4"

350mm

10 1/4"

260mm

7 1/4"

180mm

9 3/4"

250mm

1 1/4"

30mm

100mm

48 1/4"

1230mm

29 3/4"

760mm

R 11 1/2"

290mm

Swing Radius

3 3/4"

100mm

74 1/2"

1890mm

34"

860mm

17 3/4"

450mm

13 1/4"

340mm

52 3/4"

1340mm

7 1/2"

190mm

3 1/2"

90mm

9 3/4"

250mm

23"

580mm

2 3/4"

70mm

43"

1090mm

150mm

78 1/4"

1990mm

Summary of Contents for Fire Deck WS-FD-6045
































Search results

Summary of Contents for Fire Deck WS-FD-6045

Reviews:

Related manuals for Fire Deck WS-FD-6045

Brands by name

Popular brands

Wood Stone Fire Deck WS-FD-6045, Installation And Operation Manual

Search results

Summary of Contents for Fire Deck WS-FD-6045

Reviews:

Related manuals for Fire Deck WS-FD-6045

Brands by name

Popular brands