wood shark 2275 Instruction Manual Download Page 3

3

IDENTIFICATION OF SYMBOLS

Move ON/STOP switch to

the ON position.

Slowly press primer bulb

6 times.

Pull the starter rope

sharply 5 times with your

right hand.

Pull the starter rope sharply

with your right hand until

the engine starts.

Pull choke/fast idle lever

out to the full extent (to

the FULL CHOKE posi-

tion).

Push the choke/fast idle

lever in to the HALF

CHOKE position.

Starting Reminder

SAFETY RULES

WARNING

:

Always

disconnect

spark plug wire and place wire where it can-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must

be observed to reduce the risk of accidents.

Careless or improper use of this tool can

cause serious injury.

PLAN AHEAD

S

Read this manual carefully until you com-

pletely understand and can follow all safe-

ty rules, precautions, and operating in-

structions before attempting to use the

unit.

S

Restrict the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating instruc-

tions found in this manual.

Snug

Fitting

Clothing

Safety

Shoes

Safety Chaps

Heavy Duty

Gloves

Eye

Protection

Hearing

Protection

Safety Hat

S

Wear protective gear. Always use steel-

toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip

gloves; eye protection such as non-fog-

ging, vented goggles or face screen; an

approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your

hearing. Regular users should have hear-

ing checked regularly as chain saw noise

can damage hearing. Secure hair above

shoulder length.

S

Keep all parts of your body away from the

chain when the engine is running.

S

Keep children, bystanders, and animals a

minimum of 10 Meters away from the work

area. Do not allow other people or animals

to be near the chain saw when starting or

operating the chain saw.

S

Do not handle or operate a chain saw

when you are fatigued, ill, or upset, or if you

have taken alcohol, drugs, or medication.

You must be in good physical condition

and mentally alert. Chain saw work is

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating a

chain saw.

S

Carefully plan your sawing operation in ad-

vance. Do not start cutting until you have a

clear work area, secure footing, and, if you

are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

S

Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw is intended for

two-handed use.

S

Operate the chain saw only in a well-venti-

lated outdoor area.

S

Do not operate saw from a ladder or in a

tree, unless you are specifically trained to

do so.

S

Make sure the chain will not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

S

Do not put pressure on the saw at the end of

the cut. Applying pressure can cause you to

lose control when the cut is completed.

S

Stop the engine before setting the saw down.

Summary of Contents for 2275
















Reviews: