www.womaster.eu
WoMaster reserves the right to make changes to this QIG or to the
product hardware at any time without notice. It is the
user’s responsibility
to determine whether there have been any such updates or amendments
herein.
Defects, malfunctions, or failures of the warranted Product(s) caused by
damage resulting from unforeseeable incidents (such as lightings, floods,
fire, etc.), environmental and atmospheric disturbances, other external
forces such as power line disturbances and surge, host computer
malfunction and virus, incorrect power input, or incorrect cabling,
incorrect grounding and damages caused by misuse, abuse and
unauthorized alteration or repair are not warranted.
・
Disclaimer
・
Support
At WoMaster, you can use the online service forms to
request the
support
. The submitted forms are stored in server for WoMaster team
member to assign tasks and monitor the status of your service. Please
feel free to write to
if you encounter any problems.
・
Warranty
5-year Global warranties
are available for WoMaster products assuring
our customers that the products shall remain free from defects in
workmanship or materials and conform in all material respects to
WoMaster
specifications,
or
Purchaser’s supplied and accepted
specifications. The warranty is limited to the repair and/or replacement,
at WoMaster sole discretion, of the defective product during its warranty
period.
The
customer
must
obtain
a
Return
Merchandise
Authorization (RMA)
approval code prior to returning the defective
Product to WoMaster for service. The customer agrees to prepay
shipping charges, to use the original shipping container or equivalent,
and to insure the Product or assume the risk of loss or damage in transit.
Repaired or replaced products are warranted for ninety (90) days from
the date of repair or replacement, or for the remainder of the original
product's warranty period, whichever is longer.
LED
Status
Description
PoE
Loading
Green On
PoE loading is below than 25% or
50%
Amber On
PoE loading is between 51% to 75%
Red On
PoE loading is higher than 75%
PoE LED
1~24
Amber On
PoE delivering in progress
Amber Off
PoE is disabled
PWR
Green On
Power is On
Off
No Power
System
LED
Green On
Ready
Green Blinking
Firmware Updating
Off
Not Ready
Ring LED
Green On
Not Owner/Normal
Green Blinking
Owner/Normal
Amber On
Abnormal
Amber Blinking
Ring Port Fail
Off
Ring is disabled
Alarm
(DO)
Red On
Any failures in port link, ping, power,
DO and DI State by SW control
Off
No failure occurs
Digital
Input (DI)
Green On
Detected Digital Input
Off
No Digital Input
Giga
Ethernet
(Port1-24)
Green On
Links established
Green Blinking
Packets transmitting/receiving
Green Off
Link is inactive
Amber On
Link Speed 1000M
Amber Off
Link speed 10/100M
SFP Port
(Port 21-28)
Green On
Links established
Green Blinking
Packets transmitting/receiving
Green Off
Link is inactive
Amber On
Link Speed 1000M
Amber Off
Link speed 10/100M
V1.0 Jan 9 2020 3160-0RP4280-00
© WoMaster Inc. All rights reserved.
・
Safety Precautions
Restricted Access Location:
The device is intended for installation
only in a Server Room or Computer Room where both these
conditions apply:
access can only be gained by service persons or by users who
have been instructed about the reasons for the restrictions
applied to the location and about any precautions that shall be
taken; and
access is through the use of a tool or lock and key, or other
means of security, and is controlled by the authority responsible
for the location.
To remove the AC power from the system, unplug each AC power
cord from the wall outlet or power supply. The power cord(s) is
considered the disconnect device to the main (AC) power. The socket
outlet that the system plugs into shall be installed near the equipment
and shall be easily accessible.
This device supports both in-band and out-of-band network management.
The user can either configure the device through the user friendly
Web/HTTPS management or remotely manage the device through the
network by console management or Telnet/SSH.
1.
Preparation for
Web management
: First of all, verify that device is
properly installed in the network and that every PC of this network can
access the switch through the web browser (Google Chrome, Internet
Explorer, Mozilla Firefox).
•
Type
http://IP_address
in your browser (the default IP address is
http://192.168.10.1/
)
•
Key in the user name and password in login screen. The default user
name is
admin
. The system will remind you to set new password in
the first login.
•
After you click OK, the Welcome page of the web-based management
interface will appear.
•
On the left side you can see the list of software features, on the right
side
– available settings.
To link with the device, please make sure that the IP Address of the
PC is located in the same subnet (
192.168.10.x
).
2.
Preparation for
Console management (using RS232 Port)
:
•
Connect console cable between your PC and the device.
•
Start -> Program -> Accessories -> Communication -> Hyper Terminal.
•
Give a name to a new console connection.
•
Choose the COM name and select correct serial settings: Baud Rate:
115200
/ Parity: None / Data Bit: 8 / Stop Bit: 1
•
After connected, type the username
admin
to login. The system will
remind you to set new password in the first login.
•
Follow the User Manual to configure the software features.
3.
Preparation for
Telnet/SSH management
: You can connect to the
device by Telnet and the command lines are the same as what you
see by console management. Below are the steps to open Telnet
connection to the switch.
•
Start -> Control Panel -> Programs -> Select
“Turn Windows features
on or
off” -> Check “Telnet Client” box -> OK.
•
Start -> Open Command prompt ->Enter
•
Type the Telnet 192.168.10.1 (or the IP address of the switch). And
then press Enter.
・
Management
SSH (Secure Shell)
The device also supports SSH console. You can remotely connect to the
switch to access command line interface. The SSH connection can secure
all the configuration commands you sent to the switch.
SSH is a client/server architecture while the Switch is the SSH server.
When you want to make SSH connection with the switch, you should
download the SSH client tool first.
SSH Client
There are many free, sharewares, trials or charged SSH clients you can
find on the internet.
For further feature configurations, please refer to User Manual.
SYS
DO
DI
SPEED
LINK/ACT
R.S.
PWR
2
1
LINK SPEED
LINK ACT
PoE ON/OFF
Status
PoE
Loading
>75%
<75%
<50%
<25%
・
LED Indication
