manualshive.com logo in svg

WOLFF HIRA-TO, Operator'S Manual, Page: 28 / 28

Share
Download
WOLFF HIRA-TO Operator'S Manual Download Page 28

L

imited Warranty

Disclaimer

Guarantee

Two year warranty from date of purchase against defective parts or workmanship with 

the exception of the sharpening and polishing discs.  Warranty limited to replacement of 

parts.  Buyer must return warranty card to manufacturer for coverage of warranty.  This 

warranty covers only the original purchaser.  Use of non-factory parts voids any warranty.  

This warranty gives you specific rights.  You may also have other rights which vary from 

state to state.  Some states do not allow limitations or implied warranties or consequential 

damages, so these may not apply to you.

There is no expressed warranty other than limited warranty stated above.  There is no im

-

plied warranty for the merchantability of for fitness for a particular purpose.  Wolff Indus

-

tries, Inc., will not be responsible for any consequential damages.  Damages are limited 

to the replacement of defective parts.

If you are not satisfied during the first (30) days, return the merchandise for a complete 

refund, less shipping.

WOLFF

INDUSTRIES, INC

Wolff Industries, Inc.

107 Interstate Park

Spartanburg, SC 29303

(800) 888-3832

(864) 587-6008

fax (864) 587-0660

www.wolffindustries.com

[email protected]

Summary of Contents for HIRA-TO





























Reviews:

No comments