Wolf L342212 Installation Manual Download Page 13

Pro Hood Liner Installation

13

wolfappliance.com/specs

Before making electrical connections, make sure the

electrical power is turned off at the service panel.

4)

Locate the cord assembly provided with the blower.

The cord assembly has two leads, black (L1) and white

(neutral). Connect these leads to the leads from the

blower, black to black and white to white. Connect all

green and bare wires together to the ground screw in

the electrical box.

5)

Plug the cord assembly into the receptacle located

near the center of the hood liner. Refer to the illustra-

tion below. Use the clips on the interior of the hood to

secure excess power cord.

6)

Place all wiring connections inside the electrical box

and reinstall the cover. Make sure all wires are secure

and that no wires are pinched between the cover and

electrical box.

IMPORTANT NOTE:

Before turning the power on to the

ventilation hood liner, make sure the blower is off.

KNOCK-OUTS

Location of knock-outs.

Location of receptacle(s).

BLOWER

RECEPTACLE(S)

In-Line and Remote Blowers

BLOWER WIRING

IMPORTANT NOTE:

Refer to specific installation instruc-

tions provided with each blower assembly for additional

mounting and wiring instructions.

1)

Remove the two knock-outs in the top plate of the

hood liner. Refer to the illustration below.

2)

Follow wiring instructions at the blower (specific wiring

instructions are provided with each blower). Run

Romex

®

wire from the in-line or remote blower to the

hood liner.

3)

Insert 6"

(152)

of Romex

®

wire through the holes on the

back plate and into the hood liner. Secure the wire to

the electrical box with an appropriate connector.

Do not run wiring through the ductwork.

All manuals and user guides at all-guides.com

Summary of Contents for L342212

















Reviews: