Wolf 808331 Instructions Manual Download Page 3

Page 3

BLOWER

DUCT CONNECTOR

DUCTING OPTIONS

BLOWER DISCHARGE POSITIONS

Blower and duct connec-

tor in horizontal discharge 

position. (Factory shipped)

DUCT CONNECTOR

Blower and duct connec-

tor in vertical discharge 

position.

BLOWER

Change 

blower

& duct 

connector 

positions

for vertical

discharge.

DUCTING 

(Vertical blower discharge)

Typical ductwork connection to a ventilator converted to 

vertical discharge.

ROOF CAP

10”

ROUND

DUCT

4½” X 18½”

TO 10” ROUND

TRANSITION

WIRING PLATE POSITION

Wiring plate mounts to side or top of housing.

HORIZONTAL POWER 

CABLE CONNECTION

VERTICAL 

POWER CABLE 

CONNECTION

WIRING

WIRING

PLATE

WHITE

TO

WHITE

BLACK

TO

BLACK

TOP / BACK

OF HOUSING

120 VAC

LINE IN

(from

range

hood)

GROUND TO

WIRING PLATE

Ventilator can be wired from outside of housing.

Use UL approved connectors to wire per local codes.

ADUSTABLE FOR VARIOUS CEILING THICKNESSES

21½"

9

1

/

2

" to

10

1

/

2

"

21½"

ADUSTABLE FOR VARIOUS CEILING THICKNESSES

10 

3

/

4

" to

11 

3

/

4

"

MOUNTING OPTIONS

21½"

1

1

/

8

"

MAX.

ADUSTABLE FOR VARIOUS CEILING THICKNESSES

Mounting brackets in 

factory-shipped position. 

(Outlet parallel to joists.)

(New construction)

12¼"

INSTALLATION WITH DUCTWORK

RUNNING ACROSS JOISTS

¼-20 hex nuts secure mounting brackets to housing. Loosen and 

re-tighten or remove and replace nuts as necessary for desired 

mounting bracket position.

Mounting brackets mounted 

to outlet sides of housing.

(Outlet perpendicular to joists.)

(New construction)

Mounting brackets flipped 

over and mounted to top of 

sides of housing.

(Outlet parallel to joists.)

(New or existing construction)

1

1

/

2

"

to

2

1

/

2

"

21½"

ADUSTABLE FOR VARIOUS CEILING THICKNESSES

Mounting brackets flipped 

over to give approx. 1” 

more clearance.

(Outlet parallel to joists.)

(New construction)

Mounting brackets mounted 

to top of sides of housing.

(Outlet parallel to joists.)

(New or existing construction)

INSTALLATION FROM ABOVE FINISHED CEILING

21½"

1½"

to

2½"

Mounting brackets flipped 

over and mounted to outlet 

sides of housing.

(Outlet parallel to joists.)

(Existing construction)

Summary of Contents for 808331









Reviews: